Pontiac Grand Safari Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Competition Cams High Energy Timing Set for ’55-’81 Pontiac 265-455, 3212.

“Competition Cams Ultra Pro Magnum Rocker Arm Set with 1.6 Ratio for Chevrolet SBC with 7/16″” Stud, 1605-16. ”

Edelbrock No: 7251 Engine Water Pump Gasket Set Chevy Small Block. Is it time to rebuild your Edelbrock mechanical water pump- No problem- these Edelbrock water pump gaskets will keep your water pump leak-free. They are manufactured from quality materials and can be installed easily without any modifications

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Edelbrock Small-Block Chevy E-Street Cylinder Heads 64cc, 5089.

“Competition Cams Magnum 8.280″” Long, .080″” Wall, 3/8″” Diameter Pushrod Set of 8, 7131-8. ”

Edelbrock part No: 7812 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

B&M Nitrous HoleShot 3600 stall for 1965-91 TH400, 425 and 1968-81 TH350, 375 (Not TH350C) transmissions is an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Nitrous Holeshot converters feature furnace brazed impeller and turbine, new precision steel alloy pump drive tube, new heavy duty needle bearings between the stator and impeller (not a thrust washer) and needle bearings between the stator and turbine. Other features include dual pattern 10.75 and 11.50-inch bolt circle, a new turbine hub, new springs and rollers in the stator and anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower that a nitrous plate system delivers. Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. These are serious converters for serious performance street cars. To prevent contamination left from worn parts being circulated in your new components causing premature wear, we strongly recommend protecting your investment by adding a B&M transmission cooler with all new transmission installations. Listed converters are NOT to be used in trans-brake applications. Not for use in trans-brake applications.

HYDRAULIC – Magnum: High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Competition Cams Cam & Lifter Kit, Oldsmobile V8 280 Magnum Hydraulic 1 Ea, CL42-231-4.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Edelbrock C-357-B Triple-Deuce Manifold for S/B Chevy 4-Bolt Carb Pattern, 5419.

Edelbrock Performer Olds 350 Intake Manifold for 307-330-350-403 Small-Block Oldsmobile, 2711.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

“Competition Cams Valve Spring, 1.384″” 2 Spring, 988-1. ”