Pontiac 6000 Air Intakes
Top Pontiac 6000 Air Intakes Categories
We carry over 33 Air Intakes in inventory for the Pontiac 6000. If you’re looking for aftermarket Air Intakes for your Pontiac 6000, check out all these categories:
Essential Pontiac 6000 Air Intakes
Holley – Street Carburetor: 500 CFM, Electric Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-80500)
from
$599.99
Street Avenger carburetors are known to bolt on right out of the box and Holley is excited to announce the addition of our new 2bbl Street Avenger models available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations; three vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included 3/8″ fuel line connection so there are no unnecessary trips back to the parts store.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Built In No Trouble Fuel Inlet Filter
- Provides Precise Fuel Control For Low End Torque/Acceleration
- Gen Iv No Trouble Power Valve
- Three Vacuum Ports [1 Pcv/Brake 1 Timed Spark 1 Full]
- Limited Lifetime Warranty Defects In Material/Workmanship
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412CT)
from
$649.99
Competition fuel curves provide safe and reliable horsepower for high performance race engines.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1029)
from
$38.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1028)
from
$36.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1911)
from
$26.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1991)
from
$16.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Dorman – GM Bumper Retainer (Part No.961-364D)
from
$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Carquest Premium – Throttle Sensor (Part No.ECC1461)
from
$53.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
Carquest Premium – Throttle Sensor (Part No.ECC1309)
from
$44.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
Wells Vehicle Electronics – Carburetor Choke Thermostat (Part No.2C1023)
from
$41.49
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
GM Genuine Parts – Fuel Injection Throttle Body Gasket Kit with Seals, Gaskets, and Diaphragm (Part No.40-707)
from
$122.99
GM Genuine Parts Fuel Injection Throttle Body Repair Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Carquest Premium – Multi-Use Connector (Part No.PTA1166)
from
$20.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Dorman – Nylon Nut – 1/4 In. (No.14) (Part No.961-351D)
from
$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Dorman – Rivet-Push In-Hole Diameter .500 In-Head Diameter 1 In-Length .900 In (Part No.45813)
from
$1.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Carquest Premium – Air Charge Temperature Sensor (Part No.WTA1078)
from
$36.99
The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
- Application matched components ensures system operation in like new condition.
Carquest Premium – Air Charge Temperature Sensor (Part No.ECA1198)
from
$25.99
The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
- Application matched components ensures system operation in like new condition.
Pontiac 6000 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Pontiac 6000
You love your 6000. So we’ve made it easier than ever to help you find Pontiac 6000 Air Intakes in our online catalog. Our inventory holds 33 aftermarket and OEM Air Intakes for your Pontiac 6000, ranging from $1.99 to $649.99.
We offer parts from 8 brands trusted to make quality Air Intakes for your Pontiac 6000. Before you buy, take some time to read through customer reviews. We currently have 337 reviews of Pontiac 6000 Air Intakes from previous customers. Some of the top rated parts include Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. with 3.0 stars.
Find your 6000 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Pontiac 6000 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Pontiac 6000
Our inventory holds Air Intakes for your Pontiac 6000 from 8 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Dorman, and Carquest Premium, all of which can keep that Pontiac happy.
We have Delphi parts available for your Pontiac 6000 in categories like Throttle Bodies & Carb Parts. Some of the top-rated Delphi parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your Pontiac 6000 across several catalog categories, including Air Cleaner Parts. Some of our most reviewed Felpro parts include:
FAQs for Pontiac 6000 Air Intakes
What are the most purchased Air Intakes for the Pontiac 6000?
Out of 33 Air Intakes for the Pontiac 6000, the most popular in our inventory are:
from
$1.99
This product is not rated
Rivet-Push In-Hole Diameter .500 In-Head Diameter 1 In-Length .900 In
Engine Air Box Clips
What are the top-rated Pontiac 6000 Air Intakes?
Top-rated Air Intakes for your Pontiac 6000 based on customer reviews/ratings are:
from
$5.99
(1)
Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In.
“You will still have to take the engine apart”
