Plymouth PB250 Performance and Racing Products

Please Select your Vehicle to See Exact Fit Parts

Essential Plymouth PB250 Performance and Racing Products

Edelbrock – Water Pump Chrysler 1969-85 318/ 360 in Polished Finish (Part No.8887)

Water Pump Chrysler 1969-85 318/ 360 in Polished Finish

from

$448.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Flowtech – Header Gasket Set (Part No.99361FLT)

Header Gasket Set

from

$20.99
Header Gasket Set

Edelbrock – Torker II 340/360 Small Block Chrysler Intake Manifold (Part No.5076)

Torker II 340/360 Small Block Chrysler Intake Manifold

from

$447.99
2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Not for mileage or emissions applications. Can be used on 318 cid if 340/360 heads used. Available in cast or polished.

Product Features:
  • 2500 to 6500 RPM High Performance Street Engines
  • Single-Plane Low-Rise Intake Good for High RPM
  • Ideal for Applications with Limited Hood Clearance
  • For Top-End HP and Adequate Throttle Response
  • Not for Mileage or Emissions Applications
  • Can be Used on 318 cid if 340/360 Heads Used
See More

Competition Cams – High Energy 206/206 Hydraulic Flat Cam (Part No.20-208-2)

High Energy 206/206 Hydraulic Flat Cam

from

$436.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

MSD Ignition – Distributor; Chrysler 318-360; Ready-to-Run (Part No.8388)

Distributor; Chrysler 318-360; Ready-to-Run

from

$635.99
MSD’s Ready-to-Run Pro-Billet distributors for Chrysler engines are the perfect upgrade from breaker points or weak electronic ignitions. These distributors feature a maintenance-free magnetic pick-up that accurately triggers the built-in powerful ignition module. This module produces a high-output spark which improves combustion in the cylinder, resulting in quick starts, a smooth idle and great performance. Just beneath the race rotor is a mechanical advance assembly so a timing curve can easily be tailored to match your application. The QPQ coated shaft is guided by a sealed ball bearing assembly for stability and endurance while a vacuum advance canister helps increase economy on those long cruises. The Ready-to-Run distributors are also a breeze to install. Simply drop it in the engine and connect three wires and you’re Ready-to-Run to your favorite cruise! The front engine mount models are designed in a special small diameter housing to clear aftermarket heads and valve covers.

Product Features:
  • Simple and clean three wire installation
  • Mech. advance assem. can be locked out for crank trigger systems
  • Supplied w/HEI Style Distributor Cap And Rotor
  • Accepts Cap-A-Dapts
  • CARB E.O. Approved
  • Advance plate and weights are fine blanked from chrome moly steel
  • QPQ coated for friction reduction
  • QPQ coated polished steel shaft; guided by sealed ball bearings
See More

FEL-PRO Performance – Performance Valve Cover Gasket Set (Part No.1607)

Performance Valve Cover Gasket Set

from

$18.99
Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:
  • Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Accel – Ignition/Electrical (Part No.8321)

Ignition/Electrical

from

$60.99


Product Features:
  • Heavy Duty Cap and Rotor Kit
  • With Brass Inserts
See More

Competition Cams – Mutha’ Thumpr 235/249 Hydraulic Flat Cam and Lifter Kit (Part No.CL20-601-4)

Mutha' Thumpr 235/249 Hydraulic Flat Cam and Lifter Kit

from

$403.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Mr. Gasket – High Performance Thermostat (Part No.4365)

High Performance Thermostat

from

$32.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 195 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$20.79
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

B & M – Automatic Shifter, Sport Shifter (Part No.80776)

Automatic Shifter, Sport Shifter

from

$371.99
The B&M Sport Shifter features, Neutral safety switch, backup light switch, lighted gear indicator and black T-Handle and cable. Fits Most 3 and 4 Speed applications.

Product Features:
  • Base Trims For Custom Fit
  • Neutral Safety Switch
  • Backup Light Switch
  • Lighted Gear Indicator
  • Black T-Handle and Cable
See More

Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)

Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny

from

$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:
  • Vibratory Polished For Good Looks
  • Optimized Street Calibration That Works Out Of The Box
  • Factory Preset Electric Choke For Easy Startups
  • Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
  • No Unnecessary Trips Back To The Parts Store
  • Limited Lifetime Warranty
  • 100% Wet Flow Tested By Holley Technicians
  • Arrives Ready To Run
See More

FEL-PRO Performance – Performance Cylinder Head Gasket (Part No.1008)

Performance Cylinder Head Gasket

from

$44.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

VALVE SEALS, TEFLON 3/8" 1 ST

from

$33.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:
  • Work with .530″ guides and 3/8″ valve stem diameter
  • Valve stem oil seals keep unwanted oil from entering the combustion chamber
  • Several different types of valve seals are offered
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 6 Piece Set (Part No.1243)

Lower Intake Manifold Gasket Set: 6 Piece Set

from

$43.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

Mr. Gasket – Valve Cover (Part No.9806)

Valve Cover

from

$96.99
Chrome plated stamped steel valve covers have a flat smooth top, with internal baffles. Tall-style cover provides extra valve train clearance. Sold as a pair. Will not fit Magnum style heads.

Product Features:
  • Fits Chrysler small block (pre-Magnum style heads)
  • Chrome plated steel
  • Tall-style covers provide extra clearance
  • Sold as a pair
  • Cadmium Plated To Resist Corrosion
  • Easy Installation
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$204.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Earls Performance Product – Brake Bleeder Screws (Part No.280035ERL)

Brake Bleeder Screws

from

$40.49
Brake Bleeder Screws

Mr. Gasket – Chrome Distributor Hold-Down Clamp (Part No.2503)

Chrome Distributor Hold-Down Clamp

from

$15.79
Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

Product Features:
  • Rolled Edges For Strength
  • Ideal For Magnetos
  • Ideal For Ignition Distributor
See More

Mr. Gasket – Header Bolts (Part No.976)

Header Bolts

from

$26.49
When installing headers you will need header bolts, factory exhaust manifold bolts won’t work. These Mr. Gasket Header Bolts are Grade 5 for strength, black oxide coated, and have a compact hex head that is ideal for use where space is minimal – your typical header flanges. Sold as a set of 14.

Product Features:
  • 14 per Package
  • Heat-Treated For Strength
  • Ideal For Tight Spaces
  • Grade 5 Material
  • Protective Black Finish
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$95.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$34.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Helping You Find the Right Performance and Racing Products for Your Plymouth PB250

You love your PB250. So we’ve made it easier than ever to help you find Plymouth PB250 Performance and Racing Products in our online catalog. Our inventory holds 82 aftermarket and OEM Performance and Racing Products for your Plymouth PB250, ranging from $8.99 to $1,398.99.

We offer parts from 11 brands trusted to make quality Performance and Racing Products for your Plymouth PB250. Before you buy, take some time to read through customer reviews. We currently have 718 reviews of Plymouth PB250 Performance and Racing Products from previous customers. Some of the top rated parts include Blaster 2 Coil: High Performance Ignition Upgrade with 4.3 stars and Thermocap Radiator Cap with 3.2 stars.

Find your PB250 Performance and Racing Products here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Plymouth PB250 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Performance and Racing Products Brands for Your Plymouth PB250

Our inventory holds Performance and Racing Products for your Plymouth PB250 from 11 trusted brands. You’ll find OEM and aftermarket parts from brands like Mr. Gasket, Holley, and FEL-PRO Performance, all of which can keep that Plymouth happy.

Top-Rated Holley Performance and Racing Products

Leading Holley Performance and Racing Products

We carry Holley brand parts for your Plymouth PB250 across several catalog categories, including Performance Fuel Systems. Some of our most reviewed Holley parts include:
Prem Street Carbs (Avengers)
from $716.99
(2)
Prem Street Carbs (Avengers)
Performance Carburetors

FAQs for Plymouth PB250 Performance and Racing Products

What are the most purchased Performance and Racing Products for the Plymouth PB250?

Out of 82 Performance and Racing Products for the Plymouth PB250, the most popular in our inventory are:
Intake Manifold Bolts
from $18.29
(12)
Intake Manifold Bolts
Performance Intake Manifolds
High Performance Thermostat
from $32.49
This product is not rated
High Performance Thermostat
Performance Engine Coolant Thermostats

What are the top-rated Plymouth PB250 Performance and Racing Products?

Top-rated Performance and Racing Products for your Plymouth PB250 based on customer reviews/ratings are:
Blaster 2 Coil: High Performance Ignition Upgrade
from $55.99
(20)
Blaster 2 Coil: High Performance Ignition Upgrade
“Fits and works well.”
Thermocap Radiator Cap
from $53.99
(17)
Thermocap Radiator Cap
“Worth the money if only for the looks. And will tell you the temp outside”
Unilite Ignition Module
from $95.99
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”