Oldsmobile Cutlass Cruiser Air Intakes
Top Oldsmobile Cutlass Cruiser Air Intakes Categories
We carry over 183 Air Intakes in inventory for the Oldsmobile Cutlass Cruiser. If you’re looking for aftermarket Air Intakes for your Oldsmobile Cutlass Cruiser, check out all these categories:
Essential Oldsmobile Cutlass Cruiser Air Intakes
Holley – Performance and Race Carburetor: 750 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80573S)
from
$1025.99
These carburetors that are intended for use with superchargers, and have a unique capability that allows their power Valves to reference the intake Manifold vacuum below the supercharger. This allows the power valve to operate as it should, based off intake manifold vacuum. A power valve provides further enrichment to the main metering system under load (low vacuum) conditions. Without this external referencing, the power valve would be reading the Supercharger boost pressure, which has no bearing on the engine load.
Product Features:
See More
Product Features:
- Tumble Polished Shiny Finish For Good Looks
- Manual Choke For Precise Cold Start Control
- Dual Accelerator Pumps For Add Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Mechanical Secondaries For Perfect Off The Line Launches
- Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
- Boost Power Valve For Proper Enrichment Under Acceleration
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 92328)
from
$28.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
Wells Vehicle Electronics – Carburetor Choke Pull-Off 1C1064 (Part No.1C1064)
from
$58.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$37.99
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)
from
$346.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Standard Main Jet Carburetor Metering Jet Size .061 (Pair) (Part No.12462)
from
$14.99
The Edelbrock 94 No. 12462 Carburetor Jets .062″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
See More
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$33.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Dorman – Steel Cup Expansion Plug 7/8 In., Height 0.340 (sold by each) (Part No.555-014)
from
$1.99
This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this engine expansion plug matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1744)
from
$28.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Carquest Premium – Air Charge Temperature Sensor (Part No.ECA1198)
from
$25.99
The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
- Application matched components ensures system operation in like new condition.
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Carquest Premium – Throttle Position Sensor (Part No.ECC1124)
from
$33.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
GM Genuine Parts – Fuel Injection Throttle Body Gasket Kit with Seals, Gaskets, and Diaphragm (Part No.40-707)
from
$122.99
GM Genuine Parts Fuel Injection Throttle Body Repair Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Dorman – Help – Throttle Return Spring (Part No.59209)
from
$10.49
This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Nylon Nut – 1/4 In. (No.14) (Part No.961-351D)
from
$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Felpro – Carburetor Mounting Gasket (Part No.60249)
from
$7.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Oldsmobile Cutlass Cruiser Air Intakes Categories
Helping You Find the Right Air Intakes for Your Oldsmobile Cutlass Cruiser
You love your Cutlass Cruiser. So we’ve made it easier than ever to help you find Oldsmobile Cutlass Cruiser Air Intakes in our online catalog. Our inventory holds 183 aftermarket and OEM Air Intakes for your Oldsmobile Cutlass Cruiser, ranging from $1.99 to $2,000.99.
We offer parts from 12 brands trusted to make quality Air Intakes for your Oldsmobile Cutlass Cruiser. Before you buy, take some time to read through customer reviews. We currently have 716 reviews of Oldsmobile Cutlass Cruiser Air Intakes from previous customers. Some of the top rated parts include Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Street Carbs with 3.4 stars.
Find your Cutlass Cruiser Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Oldsmobile Cutlass Cruiser part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Oldsmobile Cutlass Cruiser
Our inventory holds Air Intakes for your Oldsmobile Cutlass Cruiser from 12 trusted brands. You’ll find OEM and aftermarket parts from brands like Felpro, Edelbrock, and Carquest Premium, all of which can keep that Oldsmobile happy.
We have Felpro parts available for your Oldsmobile Cutlass Cruiser in categories like Carburetor Parts and Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Oldsmobile Cutlass Cruiser across several catalog categories, including Carburetor Parts and Air Cleaner Parts. Some of our most reviewed Edelbrock parts include:
from
$450.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$46.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
FAQs for Oldsmobile Cutlass Cruiser Air Intakes
What are the most purchased Air Intakes for the Oldsmobile Cutlass Cruiser?
Out of 183 Air Intakes for the Oldsmobile Cutlass Cruiser, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$35.49
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Intake Manifold Gasket Sets
What are the top-rated Oldsmobile Cutlass Cruiser Air Intakes?
Top-rated Air Intakes for your Oldsmobile Cutlass Cruiser based on customer reviews/ratings are:
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
