Oldsmobile Cutlass Calais Performance Fuel Systems

Competition Cams Fuel Pump Pushrod with Bronze Tip for Oldsmobile Rocket, 4620.

When a high pressure fuel pump is run with a steel roller cam core, the stock fuel pump pushrod is not compatible with the steel core. You can damage an expensive roller cam as a result of wear at the fuel pump lobe. COMP Cams offers several fuel pump pushrods for various applications.

Edelbrock Performer RPM Series fuel pump for SBC and W Series Chevy, 1721.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated to accommodate various plumbing situations. High output fuel flow, flows 170 gph free flow. Shutoff pressure pre-set at 8 PSI, 3/4-inch-16 inlet and outlet ports. Fittings not included.

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Each calibration has been dyno and track tested to deliver proven performance!

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Replace your old carburetor with original Holley performance 4160 carburetors. Budget-minded enthusiasts, like you, will be rewarded with maximum performance from your stock or mildly-modified engine. These Holley 4160 adjustable float carburetors are easier to tune than full race carburetors with temperamental secondary metering blocks and dual pumps. Plus, they’re available in your choice of universal or direct fit OE replacement versions with all emission provisions. Bolt-on installation and improved performance; no wonder when car guys think of carburetors, they think of Holley 4160 carburetors!

“The Edelbrock 1411 Performer Series 750 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1411 Performer Series 750 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “”hold a tune””, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.”

Looking to upgrade the fuel system in your 1978-1987 G-Body? Take out the guesswork with Holley’s new G-Body Returnless Fuel System Kit! This 1978-87 G-body Fuel System Kit was designed as a direct replacement for your factory fuel system. Includes everything required including fuel pump module, fuel level sender, regulator, fuel filters, fuel line, fittings, hardware, and all new wiring components. Designed to use factory fuel line routing and mounting locations for a clean, OEM-like install.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.

Not only does the Sniper EFI 2GC offer superior throttle response and WOT power over the carburetor, but you may also benefit from increased fuel economy! Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking EFI to the next level. The Sniper EFI 2GC system is capable of supporting 350 HP on naturally aspirated engines. Upgrade to Sniper EFI today!.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

Want to make the switch from the original Sniper EFI to Sniper 2 and don’t want to rewire your system The new Sniper 2 upgrade kits are designed to do exactly that! Included with each Sniper 2 Plug and Play upgrade system is an adapter solution that connects your existing Sniper EFI wiring harness to a Sniper 2 throttle body in minutes. Simply remove your Sniper EFI throttle body from the intake manifold, unplug all connectors, reinstall the Sniper 2 throttle body, and plug the Sniper EFI 2 adapter harness into your existing main harness. Cycle your ignition key, run a fresh wizard on the display of your choice, and enjoy the benefits of Sniper 2 EFI.

Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

Make your classic drive like a modern fuel injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

The No:1 EFI conversion system just got better. Introducing Sniper 2 EFI – a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. We took everything that we learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more.

Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

“You don’t have to be a computer wiz or tuning professional to run a sniper kit on your build. Simplicity is what we strive for! Our calibration wizard allows you to just answer a few questions about your engine and the system will begin self-tuning with no laptop required. Use the high resolution 3.5″” full color touchscreen for tuning and gauge displays. The stealth 4150 also includes transmission kick down provisions for GM TH350/400, 200R4/700R4 and Ford C4/C6 applications.”