Nissan Pulsar NX Belts and Hoses
Top Nissan Pulsar NX Belts and Hoses Categories
We carry over 64 Belts and Hoses in inventory for the Nissan Pulsar NX. If you’re looking for aftermarket Belts and Hoses for your Nissan Pulsar NX, check out all these categories:
Essential Nissan Pulsar NX Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.21432)
from
$24.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.21404)
from
$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex II Flexible Coolant Hose (Part No.25257)
from
$28.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for increased leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimal inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Warning: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia. (Part No.81071)
from
$27.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent splitting, ballooning and elongation as well as resist ozone and other detrimental environmental elements, coolants and temperature variations of -40øF (-40øC) to +257øF (+125øC). With corrugations that provide excellent hose flexibility without flattening or collapsing, the Dayco flex radiator hose also features a helical steel coil spring for increased flexibility.
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Idler Pulley, Dayco (Part No.89036)
from
$43.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.31" Diameter (Part No.B71149)
from
$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 Inch Length (Part No.87620)
from
$15.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18030)
from
$16.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86800)
from
$36.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Poly Rib Belt Serpentine Belt; 36.81 Long, 4 Rib Count (Part No.5040368)
from
$25.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Gates – Micro-V Serpentine Drive Belt (Part No.K040320)
from
$27.49
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the surface of the ribs
- Meets or exceeds all OEM specifications
- Replacement of the tensioner is recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Carquest Standard – Serpentine Belt: 36.8" Long, 4 Rib Count (Part No.368K4)
from
$19.49
Carquest Standard serpentine belts are constructed from quality materials to ensure durability and a long lifespan. We design and manufacture each Carquest Standard belt to enhance belt-to-pulley contact, maximizing load-carrying capacity and extending belt life. Our serpentine belts are built with EPDM rubber and treated polyester cord to improve durability and belt life. Carquest Standard belts are the right choice when looking for OE fit, form, and function at a great price.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
- Meets OE fit, form, and function
Dayco – Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count (Part No.5040320)
from
$34.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.99
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$59.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Gates – Automotive XL High Capacity V-Belt (Part No.9390)
from
$30.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- The fiber-filled rubber adds flexibility along the entire length of the belt and provides greater lateral stability in the pulley.
- Ground to ensure precise dimensional control of the top width and sidewall for proper adjustment to the pulley.
- Thermally active pull cords for maintenance-free operation when the strap is properly installed and tensioned
- Resistant to oil, heat, ozone, weathering, and aging for better belt life.
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL High Capacity V-Belt (Part No.9370)
from
$37.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber mount adds flexibility along the belt and provides greater lateral stability on the pulley
- Ground to ensure precise dimensional control of the top width and sidewall for proper adjustment to the pulley.
- Thermoactivated pull cords for maintenance-free performance when properly installed and tensioned
- Resistant to oil, heat, ozone, weathering, and aging for better belt life.
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL High Capacity V-Belt (Part No.9325)
from
$26.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Ground to ensure precise dimensional control of the top width and sidewall for proper adjustment to the pulley.
- Thermoactivated pull cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather, and decay to improve belt life
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL High Capacity V-Belt (Part No.9319)
from
$29.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber mount adds flexibility along the belt and provides greater lateral stability on the pulley
- Ground to ensure precise dimensional control of the top width and sidewall for proper adjustment to the pulley.
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resistant to oil, heat, ozone, weathering, and aging for better belt life.
- Meets or exceeds SAE J636C specifications
Dayco – Bottom Cog V-Belt; 39 Inch Long, Exact Fit Premium Quality (Part No.17390)
from
$14.29
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
Gates – Premium Molded Heater Hose (Part No.18801)
from
$15.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 36 Inch Length (Part No.80405)
from
$23.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Molded 90 Degree Heater Hose (Part No.28460)
from
$13.79
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- Resists electrochemical degradation and water permeation
- Use with heater hose connectors and bulk heater hose to create custom assemblies
- Compatible for coolant, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 24 Inch Length (Part No.80404)
from
$20.79
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each) (Part No.28408)
from
$1.79
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-3
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications.
Nissan Pulsar NX Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Nissan Pulsar NX
You love your Pulsar NX. So we’ve made it easier than ever to help you find Nissan Pulsar NX Belts and Hoses in our online catalog. Our inventory holds 64 aftermarket and OEM Belts and Hoses for your Nissan Pulsar NX, ranging from $0.99 to $59.99.
We offer parts from 5 brands trusted to make quality Belts and Hoses for your Nissan Pulsar NX. Before you buy, take some time to read through customer reviews. We currently have 247 reviews of Nissan Pulsar NX Belts and Hoses from previous customers. Some of the top rated parts include Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count with 4.3 stars and Idler Pulley, Dayco with 3.7 stars.
Find your Pulsar NX Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Nissan Pulsar NX part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Nissan Pulsar NX
Our inventory holds Belts and Hoses for your Nissan Pulsar NX from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Gates, and DriveWorks, all of which can keep that Nissan happy.
We have Dayco parts available for your Nissan Pulsar NX in categories like Engine Cooling Hoses and Serpentine and V Belts. Some of the top-rated Dayco parts in these categories are:
from
$23.99
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.31" Diameter
Upper Radiator Hoses
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your Nissan Pulsar NX across several catalog categories, including Serpentine and V Belts. Some of our most reviewed Dayco parts include:
FAQs for Nissan Pulsar NX Belts and Hoses
What are the most purchased Belts and Hoses for the Nissan Pulsar NX?
Out of 64 Belts and Hoses for the Nissan Pulsar NX, the most popular in our inventory are:
from
$2.49
This product is not rated
Safety Stripe Standard Straight Heater Hose (Sold by foot)
Coolant Hoses
from
$1.99
This product is not rated
Straight Heater Hose; EPDM Rubber, 5/8 Inch Diameter (sold by foot)
Heater Hoses
What are the top-rated Nissan Pulsar NX Belts and Hoses?
Top-rated Belts and Hoses for your Nissan Pulsar NX based on customer reviews/ratings are:
from
$43.99
(6)
Idler Pulley, Dayco
“Fits correctly as long as you have the 17mm OD 12 mm ID spacer for it. The retaining washer must be installed correctly so that it doesn’t hold the ou”
from
$27.99
(5)
Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia.
“Replacing possibly damaged hose, secondary to overheating, and unknown age of the component.”
