Merkur Scorpio Belts and Hoses
Top Merkur Scorpio Belts and Hoses Categories
We carry over 16 Belts and Hoses in inventory for the Merkur Scorpio. If you’re looking for aftermarket Belts and Hoses for your Merkur Scorpio, check out all these categories:
Essential Merkur Scorpio Belts and Hoses
ContiTech – Drive Belt (Part No.W10002499364CON)
from
$12.13
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
ACDelco – Professional High Capacity V-Belt (Part No.W1000578575ACD)
from
$37.90
ACDelco Professional, premium aftermarket V-Belts serve as replacement belts for today’s most demanding engine drives. Due to thermal forces, these variable notched belts actually tighten on the drive as they get hot. This results in improved belt performance by reducing tension, decay, and noise. These premium aftermarket replacement v-belts are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Its fiber loaded rubber stock puts more flexibility along the length of the belt, yet gives the belt greater lateral stability in the pulley
- Has thermally active tensile cords that provide maintenance free performance when properly installed and tensioned
- Manufactured with form ground to ensure precise top width and sidewall dimensional control for proper fit in the pulley as well as a smoother, quieter running belt
ACDelco – Professional High Capacity V-Belt (Part No.W1000578576ACD)
from
$37.31
ACDelco Professional, premium aftermarket V-Belts serve as replacement belts for today’s most demanding engine drives. Due to thermal forces, these variable notched belts actually tighten on the drive as they get hot. This results in improved belt performance by reducing tension, decay, and noise. These premium aftermarket replacement v-belts are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Its fiber loaded rubber stock puts more flexibility along the length of the belt, yet gives the belt greater lateral stability in the pulley
- Has thermally active tensile cords that provide maintenance free performance when properly installed and tensioned
- Manufactured with form ground to ensure precise top width and sidewall dimensional control for proper fit in the pulley as well as a smoother, quieter running belt
Driveworks – Automotive V-Belt, Driveworks (Part No.40013)
from
$5.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Driveworks – Automotive V-Belt, Driveworks (Part No.35017)
from
$5.49
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 40 Inch Long, Exact Fit Premium Quality (Part No.15400)
from
$16.29
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Dayco – Flex Radiator Hoses; EPDM Rubber, 19.5 In. Long, 1.5 In. to 1.25 In. Inner Dia. (Part No.81091)
from
$19.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 Inch Length (Part No.80401)
from
$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Premium Molded Heater Hose (Part No.18799)
from
$40.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 24 Inch Length (Part No.80404)
from
$18.79
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 6 Inch Length (Part No.87661)
from
$37.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 Inch Length (Part No.87698)
from
$14.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18868)
from
$34.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Merkur Scorpio Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Merkur Scorpio
You love your Scorpio. So we’ve made it easier than ever to help you find Merkur Scorpio Belts and Hoses in our online catalog. Our inventory holds 16 aftermarket and OEM Belts and Hoses for your Merkur Scorpio, ranging from $5.49 to $40.49.
We offer parts from 5 brands trusted to make quality Belts and Hoses for your Merkur Scorpio. Before you buy, take some time to read through customer reviews. We currently have 36 reviews of Merkur Scorpio Belts and Hoses from previous customers. Some of the top rated parts include Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 19 Inch Length with 5.0 stars and Automotive RPF Raw Edge Cogged Belt with 5.0 stars.
Find your Scorpio Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Merkur Scorpio part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Merkur Scorpio
Our inventory holds Belts and Hoses for your Merkur Scorpio from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Gates, and ContiTech, all of which can keep that Merkur happy.
We have Driveworks parts available for your Merkur Scorpio in categories like Serpentine and V Belts. Some of the top-rated Driveworks parts in these categories are:
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your Merkur Scorpio across several catalog categories, including Radiator Hoses and Serpentine and V Belts. Some of our most reviewed Dayco parts include:
FAQs for Merkur Scorpio Belts and Hoses
What are the most purchased Belts and Hoses for the Merkur Scorpio?
Out of 16 Belts and Hoses for the Merkur Scorpio, the most popular in our inventory are:
from
$19.49
This product is not rated
Flex Radiator Hoses; EPDM Rubber, 19.5 In. Long, 1.5 In. to 1.25 In. Inner Dia.
Coolant Hoses
What are the top-rated Merkur Scorpio Belts and Hoses?
Top-rated Belts and Hoses for your Merkur Scorpio based on customer reviews/ratings are:
from
$24.49
(1)
Automotive RPF Raw Edge Cogged Belt
“Also known as Dayco Upgrades. Still going strong on my ’84 Toyota Supra. However my alternator is acting erratic going from 10 volts up to 18 volts. I”
