Mercury Custom Air Intakes
Top Mercury Custom Air Intakes Categories
We carry over 103 Air Intakes in inventory for the Mercury Custom. If you’re looking for aftermarket Air Intakes for your Mercury Custom, check out all these categories:
Essential Mercury Custom Air Intakes
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1920)
from
$44.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1784)
from
$22.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Holley – Street Carbs (Part No.0-8007)
from
$849.99
Classic Holley carbs have been a staple for rodders around the world for decades. They’re calibrated for use on stock to mildly modified vehicles and have that classic Holley look. Holley’s 0-8007 is calibrated and intended for small V8s or 6 cylinder engines as well as 2×4 street tunnel ram style set ups. Plus, it is Gold Dichromate coated for durability and classic Holley looks. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Factory Preset Elec Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow-Out Protection
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80903HB)
from
$1649.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 8903)
from
$16.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9361 B-1)
from
$22.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Edelbrock – Slingshot Dual-Carb Intake Manifold for 1938-53 Ford Flathead (Part No.1103)
from
$703.99
Edelbrock part #1103 Slingshot intake manifold for 1938-48 engines is a reproduction of the original intake manifold designed by Vic Edelbrock Sr. in 1938. The Slingshot is a real show stopper and even includes stainless acorn nuts for mounting the two ha
Product Features:
See More
Product Features:
- Slingshot Manifold
- Dual Plane Type-3-Bolt Style Flange
- 7.625 in. Front Height, 7.625 in. Center Height, 7.625 in. Rear Height
- Satin Finish
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Mercury Custom Air Intakes Categories
Helping You Find the Right Air Intakes for Your Mercury Custom
You love your Custom. So we’ve made it easier than ever to help you find Mercury Custom Air Intakes in our online catalog. Our inventory holds 103 aftermarket and OEM Air Intakes for your Mercury Custom, ranging from $3.49 to $1,949.99.
We offer parts from 5 brands trusted to make quality Air Intakes for your Mercury Custom. Before you buy, take some time to read through customer reviews. We currently have 69 reviews of Mercury Custom Air Intakes from previous customers. Some of the top rated parts include Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors with 3.0 stars and Street Carbs with 4.0 stars.
Find your Custom Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Mercury Custom part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Mercury Custom
Our inventory holds Air Intakes for your Mercury Custom from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, Holley, and FELPRO, all of which can keep that Mercury happy.
We have Felpro parts available for your Mercury Custom in categories like Intake Manifold Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Holley Air Intakes
Leading Holley Air Intakes
We carry Holley brand parts for your Mercury Custom across several catalog categories, including Carburetor Parts. Some of our most reviewed Holley parts include:
from
$599.99
(2)
Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate
Carburetors
FAQs for Mercury Custom Air Intakes
What are the most purchased Air Intakes for the Mercury Custom?
Out of 103 Air Intakes for the Mercury Custom, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
from
$60.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated Mercury Custom Air Intakes?
Top-rated Air Intakes for your Mercury Custom based on customer reviews/ratings are:
from
$16.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
“Was the wrong slip joint. Catalog was very confusing to use and misleading. Had to locate through another website.”
from
$849.99
(2)
Street Carbs
“As you would expect from Holley this is a great carb for my 6 cyl Jeep.”
