from

$417.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$230.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with stock guides and 11/32″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$221.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$30.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$39.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$395.99

HYDRAULIC – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.

Product Features:

HYDRAULIC – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.
268/268 Advertised Duration, 218/218 Duration @ .050″, .494″/.494″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$48.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$1087.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Intake Valves Are For Use w/Stock Pistons

from

$29.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$257.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 115 lbs. @ 1.700″, Open Pressure: 284 lbs. @ 1.200″
O.D.: 1.437″, I.D.: 1.039″
Single valve springs with damper
Approximately .510″ max lift at recommended installed height

from

$29.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens at 160 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully opens at Correct Temperature Consistently Regardless of engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$392.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$648.99

FE FORD HYDRAULIC CAM AND LIFTER KIT – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.

Product Features:

Cam and lifter kit for FE Ford engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.
268/268 Advertised Duration, 218/218 Duration @ .050″, .494″/.494″ Lift, 110 Lobe Separation

from

$359.99

Product Features:

Best for the Ultimate in Street High-Performance
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades

from

$314.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal
Available in Multiple Finishes

from

$141.99

Product Features:

Use W/ Valve Springs Part #5722, 5796
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$106.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$350.99

These Magnum Roller Rocker Arms for Ford V8 289-351W (Rail Type) 1968-89 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.6 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed from 8620 chromemoly steel, which is a superior material that will not flex and assures maximum lift. Their roller tip reduces friction, while stiff design and superior ratio accuracy yield more effective valve lift. With a 15 to 30 horsepower increase over other rocker arms, Magnum Roller Rockers are perfect for performance applications with less than 350 lbs. open spring pressure. Don’t accept inferior products or cheap knock-offs, look for the COMP Cams logo stamped into the underside of every Magnum Rocker.

Product Features:

Ultimate street rocker designed for serious performance enthusiasts
Constructed from 8620 chromemoly steel, a superior material that will not flex and assures maximum lift
Roller tip reduces friction while stiff design and superior ratio accuracy yields more effective valve lift
15 to 30 horsepower increase over stock rocker arms
Use in any applications with less than 350 lbs. open spring pressure

from

$249.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$476.99

Rocker Arms,FS/FW 1.6 7/16 Ultra Pro Mag

from

$823.99

Holeshot 2400 for Ford 1966-1991 C6 with 332, 352, 360, 390, 406, 427, 428, 429 cid with 1.848 in. crank pilot (3) Application: Ford 1966 to 1991 C6 with 332, 352, 360, 390, 406, 427, 428, 429 cid with 1.848 crank pilot (3) Furnace brazed impeller New pre

Product Features: