Mercury Capri Fuel and Emissions Systems

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Switch monitors system pressures, aiding in proper and efficient control of the compressor, fans and system levels. An improperly functioning A/C Pressure Switch will provide erratic or inaccurate actuation and operation, severely affecting system performance and function. Without reliable and accurate actuation from a properly functioning A/C Pressure Switch, critical components and the system as a whole are left unregulated and unprotected which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

• Made to OE spec to ensure a proper fit, form and function.
• Sensors are engineered for precision performance, durability and a long service life.
• All units are tested using advanced end-of-line equipment that pressurize the A/C Pressure Switch, confirm proper calibration and functionality, and check for leaks to ensure each A/C Pressure Switch meets manufacturing specifications before packaging.

The EGR system is an emission control device designed to recirculate exhaust gas into the engines air intake system and back to the combustion chamber to control nitrogen oxides or NOx. The chemical NOx is created when oxygen and nitrogen are heated above 2,800-degree F. Exhaust gas, or gas that is displaced from the combustion chamber, contains little to no oxygen molecules. By recirculating this gas back into the combustion chamber fewer oxygen molecules are available for the combustion event which will therefore create a cooler combustion event. The EGR valve can be actuated by engine vacuum or electronically by the engine control module.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Our EGR valves are designed to match the vehicle specific exhaust gas flow rate as designed by the engine manufacturer to provide clean tail pipe emissions.
• Feedback EGR valves and pressure sensors contain a robust circuit board design which increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• Where applicable stainless-steel sleeves used over cold rolled sleeves providing smooth EGR pintle operation under all operating conditions.

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Innovative engineering, manufacturing technology and quality control ensure that Spectra Premium fuel tank filler necks meet or exceed the performance of the original equipment they replace.

Product Features:

• Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertise
• Unit is dual coated for enhanced corrosion protection
• Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
• Unit is leak tested after production to ensure product in free from fuel and / or evaporative leaks
• Tested with OE fuel cap to prevent evaporative emission and check engine light failure

Carquest Premium exhaust gas recirculation (EGR) valves are designed to perform in harsh engine environments and meet or exceed original equipment (O.E.) specifications. Our Carquest Premium EGR valves are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Carquest Premium EGR valves undergo extensive validation testing to ensure long-lasting performance and reliability. Carquest Premium EGR valves are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Precision engineering and robust design to withstand harsh under hood environment
• Gaskets or seals are included if required for installation
• Extensive design validation testing and 100% end-of-line tested
• Where applicable stainless-steel sleeves used over cold rolled sleeves providing smooth EGR pintle operation under all operating conditions.
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

CARQUEST’S line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the U.S.A. Each injector is 100% tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function. Each injector includes new external seals and O-rings.

Product Features:

• Each unit is 100% tested to OE specifications
• Includes new O-rings and seals made of premium OE quality materials
• Includes application specific technical bulletin, where applicable

DENSO Oxygen Sensors are manufactured and tested to the strictest OE standards for unparalleled performance. Each component is precision built for exact replacement, and a first time fit. This innovative line features DENSO’s exclusive aluminum oxide trap layer, designed to protect the ceramic element from silicone and lead poisoning for improved engine performance, greater fuel efficiency, and unparalleled longevity. DENSO gives you the right part and the right fit.

Product Features:

• Specifically designed to meet the increasing demands of today’s engines
• 100 percent checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
• Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
• Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
• Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination

This fuel tank vent valve is designed to match the fit and function of the original valve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this fuel tank vent valve is designed to match the fit and function of the original valve on specified vehicles
• Restores functionality – this valve is made to fit and fully restore part functionality after the original valve fails
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Building upon a foundation of premium full-line products established under NGK ignition and oxygen sensor products, NTK’s expansion to technical sensors is part of our ongoing commitment to streamline product types and increase coverage under one premium brand NTK, The Sensor Specialist. With over 80 years of automotive expertise, NGK’s family of automotive products are driven by extreme dedication to innovation, performance and quality. is the only OE supplier with a full line of technical sensors in the aftermarket for import and domestic vehicles. Drawing from OE experience, sensors undergo extreme testing conditions that include thermal shock, vibration and OBD verification. sensors are manufactured to ensure a quality that meets or exceeds OE specifications. As new vehicles incorporate connected and automated technologies, trust The Sensor Specialist for full-line market support and OE application technology.

Product Features:

• The Manifold Absolute Pressure Sensor (MAP) provides manifold pressure information to the Engine Control Unit (ECU). The data is used to determine the air mass flow rate and required fuel for optimum combustion and ignition timing.
• NTK’s Manifold Absolute Pressure Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper manifold pressure, fuel metering and ignition timing.

Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.

Product Features:

• Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
• Delphi pumps are designed to operate under extreme temperatures with quick engine starts and to avoid low-fuel hesitation, including alcohol fuels and blends
• Metal tubes in Delphi hangers are routed so as to not contact the tank or vehicle underbody at any point eliminating noise and vibration during vehicle operation
• Empty float height and float retention matches OE specifications and guarantees correct gas gauge reading
• Restores fast pressure performance and system integrity, translating to better pumping through less energy
• Lower failure rates due to its innovative design and durability
• Part is validated, tested and matched to the right vehicle application
• Lower amperage draws less load on vehicle’s electrical system
• Always be sure to check and clean fuel tank to avoid unnecessary returns

New Platinum Pro Fuel Tank Straps

Product Features:

• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

This fuel injection idle air control valve gasket is designed to match the fit and function of the original gasket on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this fuel injection idle air control valve gasket is designed to match the fit and function of the original gasket on specified vehicles
• Restores functionality – this gasket is made to fit and fully restore part functionality after the original gasket fails
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Carquest Premium idle air control valves are designed to perform in harsh engine environments and meet or exceed original equipment (O.E.) specifications. Idle air control valves, or sometimes known as idle air motors, are used to maintain the engine speed at idle by precisely adjusting the amount of air allowed to enter the intake. Our Carquest Premium idle air control (IAC) valves are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Carquest Premium idle air control valves undergo extensive validation testing to ensure long-lasting performance and reliability. Carquest Premium idle air control valves are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Precision engineering and robust design to withstand harsh under hood environment
• Gaskets or seals are included if required for installation
• Extensive design validation testing and 100% end-of-line tested
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

This fuel pump harness connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this fuel pump harness connector matches the appearance and function of the factory hardware on specified applications
• Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Product Features:

• Premium OE quality materials

The ACCEL premium quality fuel pressure regulators provide stable fuel pressure under the most demanding conditions. Adjustable Fuel Pressure Regulators allow adjustments for increased fuel volume and superior fuel atomization. Stock Ford 5.0L systems operate at 39 psi

Product Features:

• Premium quality pressure regulators provide stable fuel pressure under the most demanding conditions
• Adjustable fuel pressure regulators allow adjustments for increased fuel volume & superior fuel atomization
• Boost sensitive design
• Allow Adjustment For Increased Fuel Volume/Fuel Atomization
• Boost Sensitive Design

CARDONE Remanufactured Smog Pumps are engineered for quick installation and no comebacks. These pumps come with all necessary components for easy installation, while other brands leave out integral components, such as inlets and outlets that commonly break during installation. CARDONE engineers pay special attention to proper vane size and shape on each application to maintain proper flow, while other brands consolidate vane sizes for their own convenience.

Product Features:

• 100 percent testing of all units guarantees reliable performance every time.
• High temperature grease extends bearing life, resulting in longer pump life.
• New carbon shoes/vanes on every unit ensure accurate air output to meet today’s stringent emissions standards.
• Guaranteed fit and function.
• Meets or exceeds O.E.M performance.

Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.

Product Features:

• Protects your fuel from theft and vandalism
• Passes all state and federal emissions tests
• Manufactured from durable, long-life materials
• Reduces air pollution with proper sealing and venting
• Independently tested for emission control

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.

Product Features:

• Filtration performance and micron rating meet or exceed OE requirements
• OE replacement strainer designed for use with Delphi electric fuel pumps
• Replacing the strainer is always recommended when replacing a fuel pump

This fuel tank sending unit is designed to match the fit and function of the original unit on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this fuel tank sending unit is designed to match the fit and function of the original unit on specified applications
• Restores functionality – reliable replacement for an original part that has failed due to internal sensor failure
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function