Name: Vacuum Brake Booster: Without Master Cylinder
Brand: Wearever
SKU: 53-2932
Price: 158.99 USD

from

$158.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$80.33

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$24.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features:

Dependable stopping power
Single layer shim for quiet braking
OE-designed slots and chamfers to reduce noise and vibration
Powder-coated backing plate prevents corrosion

from

$6.79

Brake Press. Sw. Boo

from

$29.99

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

Wearever Brake Shoes come bonded or riveted based on OE design.
Wearever Brake Shoes are coated to prevent rust.
Wearever Brake Shoes are 100% New not remanufactured.
Brand may vary by location

from

$221.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Includes 2 Front Sensor Wires
Buy with confidence from the originator & industry leader of brake kits

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$4.89

As an OE manufacturer, PEX brake wear sensors are designed and produced to have the same form, fit, and function as the original OE part. This means technicians get the right part for the job, the part fits properly, and the brake wear sensor works correctly once installed. This insures that as the brake pad wears down, the sensor makes proper contact with the rotor, which breaks the sensor’s wire loop. Once broken, the car’s warning lamp is illuminated, alerting the driver that the brake pads have worn to a level in which they need to be replaced.

Product Features:

PEX sensors are designed and produced to have the same form, fit, and function as the original OE part enabling easy installation and ensuring proper fit.
Use of high quality materials specified by auto manufactures ensures durability and resistance to extreme temperatures, as well as excellent electrical performance and provides safety and performance for drivers and passengers.
All PEX products undergo stringent and constant quality controls. We inspect virtually every aspect going far beyond the form, fit, and function. Our Quality Control includes heat tests; resistance; as well as pull force testing – just to name a few.
Our newly designed packaging is both cost effective and “green” since it is manufactured using fewer natural resources reflecting our dedication to corporate responsibility
As the leading manufacturer of electronic brake wear sensors, PEX offers the widest range of sensors in our peer group for both commercial and passenger vehicles.

from

$17.99

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$17.99

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$90.69

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$74.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to prevent warping
Air gap eliminates brake fade and increases pad life
Non-Directional finish decreases break-in time

from

$1.21

Oil Drain Plug Gasket

from

$101.99

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Plastic reservoirs are vacuum-tested to ensure they are leak free.

from

$19.99

Carquest Standard brake pads are designed for original equipment (O.E.) fit, form and function for dependable stopping while providing great value. Our brake pads use quality friction formulas for reliable stopping power. Carquest Standard brake pads feature a single-layer shim that absorbs noise and vibration to provide quiet braking. These brake pads also utilize slots and chamfers based on the OE design. Carquest Standard brake pads are the right choice when looking for good performance at a great price.

Product Features: