from

$29.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$16.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$115.99

CARDONE Remanufactured ABS Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. Every CARDONE unit goes through stringent testing, ensuring like-new performance and quick reaction time when traction control is required.

Product Features:

Worn-out, missing or non-functioning components are replaced with new or rebuilt components, where necessary.
Critical components are re-soldered, where necessary, to ensure superior electrical connections, eliminate intermittent failures and extend product life.
100 percent computer testing ensures consistent performance.
Air-decay testing ensures unit is void of brake fluid.
On-car testing is done, when necessary, for validation of product reliability.
High-pressure hydraulic testing ensures zero leakage.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.

from

$194.99

ABS carrier case exciter ring (tone ring) with 108 teeth for 8.8″ Ford.

Product Features:

ABS tone ring for Ford 8.8″
108 tooth

from

$29.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing ¿ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ¿ in the part design process ensures speed-to-market and a precise fit guaranteed.
Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$161.99

CARDONE remanufactured ABS Hydraulic Assemblies are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. Every unit goes through stringent testing, ensuring like-new performance and quick reaction time when traction control is required.

Product Features:

New O.E.-quality seals are used in the remanufacturing process to ensure top performance and reliability.
Worn-out, missing, or non-functioning components are replaced with new OE-quality components.
100 percent computer testing ensures consistent performance.
High-pressure hydraulic testing ensures zero leakage.
Air-decay testing ensures unit is void of brake fluid.
On-car testing is done, when necessary, for validation of product reliability.