Mazda MX-5 Miata Engine Cold Air Intakes

K&N’s Universal Air Filters are designed and manufactured for a wide variety of applications including racing vehicles, radio-controlled cars, generators, snowmobiles, tractors, and other applications. Regardless of the angle or offset diameter of the air intake, there is probably a K&N Universal air filter for your equipment. All filters are constructed with ultra-strong molded pliable rubber flanges which absorb vibration and allow for secure attachment and can also be stretched for up to 1/16 of an inch (1.5mm) to fit in-between sizes. K&N universal air filters are washable and reusable.

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.

The K&N 69-6010TR Typhoon cold-air intake system is a free-flowing, mandrel-bent aluminum tube air induction system designed to fit some Mazda 3 and Mazda 5 models. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon cold-air intake which is designed to pull in relatively cooler air and dramatically reduce air flow restriction by smoothing and straightening air flow. This allows your engine to inhale a larger amount of denser air than the factory air intake. More air means more usable power and acceleration throughout the engine’s RPM range. The 69-6010TR cold-air intake consists of a black rubber topped K&N high-flow air filter that directs cooler outside air through free-flowing aluminum tubing into a short ram induction tube that delivers high volumes of clean, colder air into the engine’s throttle body for a guaranteed power gain. The oversized cone shaped air filter comes with a water repellent DryCharger filter wrap to protect the filter from moisture. The air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media.

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes.

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media.

The AEM-21-786C Performance Cold Air Intake System produces horsepower And torque gains by replacing your vehicle’s restrictive factory air filter And air intake housing. This air intake system was designed, tuned And dyno-tested to fit select Mazda MX-5 Miata models. Air enters the system through an oversized AEM Dryflow synthetic washable air filter for outstanding air flow, filtration And performance. The air filter is located in the original air box space And is protected by a heat shield which is designed to reduce intake air temperature And increase horsepower. Attached to the heat shield is an aluminum coolant overflow reservoir that replaces the stock reservoir so that the air intake will fit properly. The air intake tubing is constructed from mandrel-bent aluminum featuring a durable gunmetal gray powder coated finish. This air intake system was developed to accommodate the engine’s factory emissions control devices including the mass air flow sensor And PCV hose. The tapered cylinder shaped AEM Dryflow air filter is made from an oil-free, synthetic filter media that can be used for up to 100,000 miles before cleaning is needed (depending on driving conditions). The air intake system is easy to install with commonly available tools. Some AEM air intakes are not legal for sale or use in California And other states adopting California emission standards, while others are 50 state legal. View the 21-786C vehicle applications to determine the legal status for each vehicle.

“Large Three Layer Performance Air Filter:Momentum’s unique filter-to-housing interface was built to feature the largest air filter possible. This 7-1/2″” tall 360-degree radial flow air filter features our oil-free Pro DRY S media with three layers of synthetic media for maximum convenience. Its progressive layering provides great filtration efficiency and dust holding capacity, while not requiring the use of oils. This media is best suited for street use. Its inverted top makes for more filter surface area, resulting in longer service intervals.Unique One-Piece Housing:The smooth one-piece sealed housing, constructed of heat-resistant cross-linked polyethylene (XLPE), features our patent-pending filter-to-housing interface. Its innovative design resembles the original Miata logo and minimizes the total number of parts used. A large, clear sight window allows for hassle-free filter inspection, without having to disassemble your system. An auxiliary air inlet can be used, or closed with a supplied plug.Dyno-Tuned Intake Tube:This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat soak resistant and extremely durable.Premium Components:Stainless-steel clamps and a silicone coupling are included for strength and durability, while also providing the most secure installation available. This Momentum intake utilizes factory mounting locations and is designed with fewer parts, making for a fast and easy installation.”

“Large Five Layer Performance Air Filter:Momentum’s innovative filter-to-housing interface was built to feature the largest air filter possible. This 7-1/2″” tall 360-degree radial flow air filter features our pre-oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum performance. Our Pro 5R media provides your engine with the largest amount of high-flowing air, usually resulting in the highest power gains out of all our filter media options. This media is perfect for street and/or track use. Its inverted top makes for more filter surface area, resulting in longer service intervals.Unique One-Piece Housing:The smooth one-piece sealed housing, constructed of heat-resistant cross-linked polyethylene (XLPE), features our patent-pending filter-to-housing interface. Its innovative design resembles the original Miata logo and minimizes the total number of parts used. A large, clear sight window allows for hassle-free filter inspection, without having to disassemble your system. An auxiliary air inlet can be used, or closed with a supplied plug.Dyno-Tuned Intake Tube:This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat soak resistant and extremely durable.Premium Components:Stainless-steel clamps and a silicone coupling are included for strength and durability, while also providing the most secure installation available. This Momentum intake utilizes factory mounting locations and is designed with fewer parts, making for a fast and easy installation.”

“Large Five Layer Performance Air Filter: This 7 IN tall 360-degree radial flow air filter features a 3-1/2″” flange and our pre-oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum performance. It provides your engine with the largest amount of high-flowing air and delivers the highest power gains in most cases. This media is perfect for street and/or track use. Its inverted top makes for more filter surface area, resulting in longer service intervals.One-Piece Housing: The included massive air filter is surrounded by an open-element XLPE (cross-linked polyethylene) polymer housing that minimizes warm engine air for maximum performance. Its open design allows for easy viewing of the air filter, yet creates a heat-blocking seal when the vehicle’s hood is closed. It utilizes the vehicle’s OE air inlet with no additional hardware. An additional auxiliary air inlet is available for use to bring in air from the front of the vehicle when under power, or can be closed with an included plug if desired.Dyno-Tuned Intake Tube: This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat soak resistant and extremely durable.Hassle-Free Installation: This is a direct fit intake system that utilizes factory mounting points and requires no cutting or modifications. All necessary clamps, couplings, and hardware are included. Its revolutionary design, featuring our patent pending filter-to-housing interface, uses half the number of parts of a traditional cold air intake system.”

Takeda intakes are constructed out of lightweight black wrinkle finish aluminum tubing or clear-coat anodized polished tubing for maximum air flow and a great style. This intake uses a large 360 degree high flow Pro DRY S air filter for maximum flow, filtration and convenience. The Pro DRY S air filter requires no oils and cleans with simple soap and water. Takeda intakes come complete with all tubing, filters, couplers and hardware for an easy installation.

Takeda intakes are constructed out of lightweight black wrinkle finish aluminum tubing or clear-coat anodized polished tubing for maximum air flow and a great style. This intake uses a large 360 degree high flow Pro DRY S air filter for maximum flow, filtration and convenience. The Pro DRY S air filter requires no oils and cleans with simple soap and water. Takeda intakes come complete with all tubing, filters, couplers and hardware for an easy installation.