Lincoln Mark VIII Ignition Coils and Boots

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Routing spark plug wires is an art form. It takes patience and time to route your wires away from the headers, through separators and to the distributor cap. Some wire sets fit perfect, but a lot of people want to build their own so they can route them exactly how they see fit. Our Universal spark plug wire sets come with the spark plug terminal and boot installed with the other end open. Distributor cap boots and terminals are included so you can cut the wire to the desired length, then install the terminal with the supplied Mini-Stripper-Crimper. It’s a little more work, but in the end it will be worth it.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Distributor Cap – Boots and Terminals Included
• Incl. Mini-Stripper-Crimper

For Ford fans, these wires are designed for Ford Modular engines.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Distributor Cap – Boots and Terminals Included
• Includes Mini-Stripper-Crimper For Factory Style Crimps
• Size Includes Terminals/Boots For Spark Plugs

Carquest ignition coils meet original equipment (OE) fit, form and function and are built to ensure reliable starting and performance. Carquest ignition coils are tested to ensure proper spark and perfect fit for each application. These ignition coils are an affordable repair choice to restore the vehicle¿s ignition system performance. Carquest ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Long service life and durable performance
• High dielectric strength for reliability
• Corrosion-resistant connections
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413
• High reliability
• Long service life

The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles. Motorcraft and Ford Parts are used throughout Ford vehicles in a variety of applications that help ensure the proper build quality, integrity and long-lasting performance of every Ford car or truck. Motorcraft and Ford Parts are manufactured from first quality materials chosen specifically for maximum performance and application suitability. As with all Motorcraft and Ford Parts, any innovations or improvements developed since the vehicle’s manufacture are included in these after market replacement parts, ensuring the most current technology and performance.

Product Features:

• These coils provide the exact spark timing that helps maximize the engine and emissions performance
• RFI suppression helps minimize electronic noise through a Ford patented spring assembly inside the coil boot
• Engineered to help withstand temperature extremes
• Internal insulation displacement connection is helps make high-reliability internal connections
• Interior insulation helps ensure no internal arcing
• Right fit for each application; helps provide ease of installation and removal
• High grade silicone rubber boot materials do not degrade or stick, aiding in environmental and dielectric sealing
• Housings engineered to help resist cracking in the most extreme conditions
• Ford-patented iron core lamination stack integrates rare earth magnets in the flux circuit to help deliver consistent high energy required for output

ACCEL Super Coils feature advanced bobbin technology, highly specialized silicon magnetic steel cores, optimized windings, proper resistance and engineered turn ratios that deliver a high performance, quality coil. Specialized high temperature epoxy resists shock and vibration, while increasing thermal conductivity. These are direct high performance replacements for OEM coils.

Product Features:

• Specialized silicone magnetic steel cores are surrounded by precision wrapped windings using advanced bobbin technology which helps maintain the proper resistance and turn ratios necessary to deliver a improved performance spark.
• Advanced Bobbin Technology
• Direct Plug In Replacement results in a Direct OE Fit
• OBD ll Safe, so you won’t be throwing codes, just sparks
• Standard Motor Products SMP Uf-191
• MSD 8244 82448

Carquest Premium ignition coils meet or exceed original equipment (OE) specifications and are developed by top OE/OES manufacturers to ensure superior performance. All of our Carquest Premium ignition coils are developed by IATF 16949 certified manufacturers for consistent durability and long-lasting performance. These ignition coils use high-quality components and will utilize optimized designs on applications where the OE ignition coil had frequent failures. We require stringent testing standards to ensure proper fit and performance for each application and stand behind our Carquest Premium ignition coils with an industry-leading warranty. Carquest Premium ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Built by IATF 16949 certified manufacturers for consistent durability
• Coil drivers match OE for current limit, electrostatic discharge (ESD) protection and multi-spark
• Segmented secondary bobbins to distribute high voltage and prevent shorting
• Extensive design validation testing to ensure long-lasting reliability
• 100% end-of-line tested to ensure proper performance
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413

Every single Delphi ignition coil is designed and endurance tested using high quality materials. This ensures fast starts, consistent engine performance and optimized fuel efficiency. We makes more than 10 million ignition coils for North America each year, and each one is engineered to OE design specifications for vehicles from Ford, Toyota, Nissan, Lexus, GM, Mazda, Chrysler, Subaru, Acura and more.

Product Features:

• Delphi coils provide OE performance, durability and electromagnetic capacity level requirements
• Delphi ignition coils are designed to operate as part of an integral engine management system to insert power into spark plugs and ensure fast starts; consistent engine performance and optimized fuel efficiency
• Delphi uses winding process techniques to control the length of wire between adjacent windings; that’s important since more length means greater voltage differences and can create more pressure that could break down the insulation and wire coating
• We back our ignition coil design with proven materials, such as high quality wires and wire coating that resists the cracks, pin holes and imperfections that most often lead to failure issues

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Fd-478
• MSD 5527
• Standard Motor Products SMP Fd-478
• MSD 5527
• Resists Shock And Vibration
• Resists Corrosion

Carquest Premium ignition coils meet or exceed original equipment (OE) specifications and are developed by top OE/OES manufacturers to ensure superior performance. All of our Carquest Premium ignition coils are developed by IATF 16949 certified manufacturers for consistent durability and long-lasting performance. These ignition coils use high-quality components and will utilize optimized designs on applications where the OE ignition coil had frequent failures. We require stringent testing standards to ensure proper fit and performance for each application and stand behind our Carquest Premium ignition coils with an industry-leading warranty. Carquest Premium ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Built by IATF 16949 certified manufacturers for consistent durability
• Coil drivers match OE for current limit, electrostatic discharge (ESD) protection and multi-spark
• Segmented secondary bobbins to distribute high voltage and prevent shorting
• Extensive design validation testing to ensure long-lasting reliability
• 100% end-of-line tested to ensure proper performance
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413

Every single Delphi ignition coil is designed and endurance tested using high quality materials. This ensures fast starts, consistent engine performance and optimized fuel efficiency. We makes more than 10 million ignition coils for North America each year, and each one is engineered to OE design specifications for vehicles from Ford, Toyota, Nissan, Lexus, GM, Mazda, Chrysler, Subaru, Acura and more.

Product Features:

• Delphi coils provide OE performance, durability and electromagnetic capacity level requirements
• Delphi ignition coils are designed to operate as part of an integral engine management system to insert power into spark plugs and ensure fast starts; consistent engine performance and optimized fuel efficiency
• Delphi uses winding process techniques to control the length of wire between adjacent windings; that’s important since more length means greater voltage differences and can create more pressure that could break down the insulation and wire coating
• We back our ignition coil design with proven materials, such as high quality wires and wire coating that resists the cracks, pin holes and imperfections that most often lead to failure issues

As the innovator and leader in stick coil technology DENSO has conducted superior testing and inspection processes to insure the highest quality ignition coil. Don’t be fooled by imitations – look for the DENSO name to be sure you’re getting the best.

Product Features:

• First Time Fit
• Built to DENSO Original Equipment Standards

Carquest Ignition Coils ensure fast starts, consistent engine performance and optimized fuel efficiency at an affordable cost.

Product Features:

• High output
• Long spark duration
• High dielectric strength
• Corrosion resistant connections
• High reliability
• Long service life

As the innovator and leader in stick coil technology DENSO has conducted superior testing and inspection processes to insure the highest quality ignition coil. Don’t be fooled by imitations – look for the DENSO name to be sure you’re getting the best.

Product Features:

• First Time Fit
• Built to DENSO Original Equipment Standards

Designed to be used with late model Ford waste spark ignition systems. 83:1 turns ratio and lower primary resistance produce high voltage output. Secondary towers designed for snap on spark plug terminals. Primary terminals require Ford style connector. Carb O.E. approved.

Product Features:

• Designed to use w/late model Ford waste spark ignition systems
• 83:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Secondary towers designed for snap on spark plug terminals
• Primary terminals require Ford style connector

NGK ignition coils are manufactured to meet or exceed OE standards for the highest durability and operational performance, so they can be installed with confidence. NGK and their family of automotive products have over 80 years’ experience and are driven by extreme dedication to innovation, performance and quality. With state-of-the-art manufacturing, inventory and distribution facilities in North America and globally, NGK is dedicated to providing customers with world-class products and services. Developed and rigorously tested in our ISO 17025 accredited test lab under the most extreme conditions, NGK’s coil designs will outperform all others – far beyond operational environments a vehicle would actually experience. NGK ignition coils have vast coverage including late-model domestic and import vehicles. NGK’s OE legacy, unsurpassed quality and leading vehicles in operation coverage reinforces NGK as The Ignition Specialist.

Product Features:

• OE QUALITY: Vacuum-sealed premium epoxy resin and thermoplastic coil housings provide superior dielectric strength, voltage insulation and durability
• OPTIMAL PERFORMANCE: Precision coil windings and laminations maximize outputs, custom NGK ASIC chipset optimizes efficiency, prevents component damage
• EASE OF INSTALLATION: NGK Ignition Coils include ignition control module, premium high temperature coil boot, and jumper harnesses where required
• THE NGK DIFFERENCE: Featuring superior materials and design enhancements
• EXTENSIVE TESTING: NGK ignition coils must pass extreme testing during manufacturing to ensure the highest quality and durability standards are met
• PRODUCT ENGINEERING: Advanced flow and stress modeling systems preemptively identify and avoid common failure points found in OE and competitor coils