Lincoln Mark VII Performance Engines

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.100 inch, Compressed thickness 0.038 inch.

“Edelbrock part No: 5022 Torker-Plus Camshaft is designed for small-block Ford 289-302 V-8 applications. The camshaft works well with Torker II manifolds for performance from 2500 to 6500 rpm, this camshaft is ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft. Camshaft Specifications: – Duration at .050 Intake: 214 degrees – Duration at .050 Exhaust: 224 degrees – Lift at Valve Intake: .472″” – Lift at Valve Exhaust: .496″” – Lobe Separation: 112 Degrees – Intake Centerline: 107 Degrees”

“Edelbrock part #2921 Victor Jr. 302 intake manifold is designed for Ford 289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads such as Edelbrock #60259 and #77169 or equivalent. This intake manifold has bosses for rear water crossover. Port exit size at cylinder head is 1.08″” x 1.90″” with extra material to accommodate a 1.18″” x 2.10″” opening. This Victor Jr. is a single-plane, high-rise intake designed for maximum race-winning power at higher engine speeds.”

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

This B&M Tork Master 2400 fits 1980-92 Ford AOD transmissions with a 1.375-inch crank pilot and has a 11.4-inch bolt circle. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product.

Edelbrock part No: 7820 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Edelbrock Water Pump for Small-Block Ford 351W in Black Finish, 88433.

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

“Edelbrock Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02″”, 60399. ”

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It is a direct replacement for a factory one-piece rubber main seal. It’s also injection molded for a precise fit.

“Edelbrock Performer-Plus Camshaft No: 2122 is designed for 289-302 Ford V8 engines and produces optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2122 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 310HP and 260 Ft Lbs of Torque when paired with Performer 289 intake manifold No: 2121 and Performer cylinder heads No: 60329. Not for 1985 and later engines with roller lifters. Camshaft specifications: – Intake duration: 204 Degrees – Exhaust duration: 214 Degrees – Intake lift: .448″” – Exhaust lift: .472″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 16″””

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Edelbrock Valve Spring Retainers are made of superior quality steel and are machined and heat treated for maximum strength. They feature a black oxide finish to prevent rust and corrosion

“Competition Cams High Energy 6.248″” Long, 5/16″” Diameter Pushrod Set, 7826-16. ”

“Edelbrock part No: 9655 Pushrods are designed for small-block Ford 289-302 V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise formed wedged ends for a high quality fit with the cup seats. A black oxide finish is added for corrosion resistance. Pushrod Specifications: – For hydraulic rollers, 5.0L with stud mount. Refer to lifter kit No: 97453 – Outside Diameter: 5/16″” – Length: 6.400″””

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Competition Cams Magnum Double Row Timing Set for ’65-’88 Ford 255, 289, 302 and Boss 302, 2120.

Kormetal gasket used between the SysteMax II Ford 5.0L upper and lower manifolds.

Edelbrock part No: 7220 Intake Gaskets for 1963-1996 Small-Block Fords allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-2N Micropore technology does not use solvents making our gaskets environmentally friendly. Impervious to most chemicals, this synthetic fiber composite provides a high recovery under load. This means that when compressed, the gasket will conform to any imperfections on the sealing surface even using lower flange pressures. A nitrile bead around each port opening makes the seal even better.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.