Jeep J-200 Air Intakes
Top Jeep J-200 Air Intakes Categories
We carry over 100 Air Intakes in inventory for the Jeep J-200. If you’re looking for aftermarket Air Intakes for your Jeep J-200, check out all these categories:
Essential Jeep J-200 Air Intakes
Holley – Street Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-1850C)
from
$599.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow Out Protection
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
- Compensates For All Vehicle Weights Gearing/Transmissions
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$60.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$47.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Felpro – Carburetor Mounting Gasket (Part No.60102)
from
$4.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Crown Auto Jeep Replacmnt – OE Replacement, For Part Numbers J5357373/ J5362090. (Part No.J0941521)
from
$1.99
Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.
Product Features:
See More
Product Features:
- Crucial Gaskets Are Required To Avoid Dangerous Fuel Leaks
- Offers OE Fit And Function
- Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts
- Long-Lasting, Durable Crown Automotive Products
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$17.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Jeep J-200 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Jeep J-200
You love your J-200. So we’ve made it easier than ever to help you find Jeep J-200 Air Intakes in our online catalog. Our inventory holds 100 aftermarket and OEM Air Intakes for your Jeep J-200, ranging from $1.99 to $1,949.99.
We offer parts from 5 brands trusted to make quality Air Intakes for your Jeep J-200. Before you buy, take some time to read through customer reviews. We currently have 99 reviews of Jeep J-200 Air Intakes from previous customers. Some of the top rated parts include Street Carbs with 3.4 stars and Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate with 4.5 stars.
Find your J-200 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Jeep J-200 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Jeep J-200
Our inventory holds Air Intakes for your Jeep J-200 from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, Holley, and FELPRO, all of which can keep that Jeep happy.
We have Edelbrock parts available for your Jeep J-200 in categories like Carburetor Parts. Some of the top-rated Edelbrock parts in these categories are:
from
$18.99
(1)
Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors
Carburetor and Injector Mount Gaskets
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Carburetors
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Jeep J-200 across several catalog categories, including Carburetor Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$16.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
Carburetor and Injector Mount Gaskets
FAQs for Jeep J-200 Air Intakes
What are the most purchased Air Intakes for the Jeep J-200?
Out of 100 Air Intakes for the Jeep J-200, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$60.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated Jeep J-200 Air Intakes?
Top-rated Air Intakes for your Jeep J-200 based on customer reviews/ratings are:
from
$599.99
(2)
Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate
“REPLACED EXHISTING HOLLEY CARB,LIKE THE PRODUCT LOOKS GOOD ON ENGINE, POLISHED ,EXCELLENT CARBS USED ON OTHER PROJECTS”
