Jeep CJ6 Differential Cross Pins

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Dana Spicer 44
• Fits standard open differentials only

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Power Lok positraction only

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Dana Spicer 30
• Works with Spartan Locker or standard open spider gears

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Dana Spicer 30
• Fits standard open differentials only

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, pinion nut, pinion seal, marking compound and brush.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Dana Spicer 44 and Spicer 44HD
• Works with Spartan Locker or standard open spider gears

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Chrylser 8.25″ with 27 and 29 spline axles
• Works with Spartan Locker or standard open spider gears

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Dana Spicer 44HD
• Fits standard open and Trac Loc applications

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Chrysler 8.25″
• Fits standard open differentials only

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. .

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Dana Spicer 60
• Works with Spartan Locker or standard open spider gears

Model 35 Spartan locker cross pin, double drilled for roll pin or cross pin bolt designs.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits AMC Model 35
• Works with Spartan Locker or standard open spider gears

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. Side shims included.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Dana Spicer 44
• Works with Spartan Locker or standard open spider gears

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits AMC Model 20
• Works with Spartan Locker or standard open spider gears

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits AMC Model 35
• Cross pin bolt design
• 0.716″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits AMC Model 35
• Cross pin bolt design
• 0.685″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Jeep JK non-Rubicon rear

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits AMC Model 35
• Roll pin design
• 0.685″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
• Fits standard open differentials only
• 0.750″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Roll pin for Chrysler 8.75″, Ford 8″ and 9″, AMC Model 20 and Model 35
• 0.260″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Floater roll pin
• Fits Dana Spicer 44 and Chrysler 8.75″
• Power Lok positraction only