Jeep CJ5 Performance and Racing Products

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Own a Jeep? The toughest four letter word on wheels. Are you looking for a parts source rugged enough to match your off the beaten path sense of adventure? With more than 11,000 unique part numbers from brands like Omix-ADA, Rugged Ridge, Alloy USA, Outland Automotive, ORV Suspension and Precision Gear, consider this your trail guide to the 4×4 of your dreams. A go anywhere, anytime, in any weather vehicle. Go ahead and smile, because it’s going to take a lot of courage not to be cocky when you Own a Jeep like that? Omix-ADA is more than just a parts manufacturer, they’re a community of enthusiasts dedicated to producing the finest in off-road solutions. Our products have been propelling four-wheel drive vehicles down highways, back roads and over the world’s roughest terrain for about two decades. Omix’s team of engineers have developed, tested and trail ridden many of our 11,000+ products until they were perfected for you. Omix-Ada is proud to have one of the most capable Research and Development, Engineering, and Product Design teams in the automotive aftermarket. By utilizing the latest in 3D Computer Aided Design and Finite Element Analysis, and coupling these tools with our decades of market experience, we are able to develop products that give our customers the highest value parts possible.

Product Features:

• 1969-1971 CJ5, Full Brake Line Set (12 Pieces), With Drums, Stainless Steel

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Is your Jeep running rough? Over time ignition parts will deteriorate. It’s easier to replace them now than to have a roadside breakdown in the future. Order high quality ignition parts from Omix-ADA to get your Jeep running smooth again.

Product Features:

• 12 Volt
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Is your Jeep’s steering loose? Are your tires wearing in an uneven pattern? Chances are that some of your steering components are worn. Fixing them is cheaper than replacing your tires and it’s a whole lot safer too. Omix-ADA offers high quality replaceme

Product Features:

• Steel
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Timing chains stretch over time. If left untouched, they can begin jumping teeth on the camshaft and crankshaft sprockets. This will change your timing and will do major damage to your Jeep’s engine. It is recommended that you change the timing chain and

Product Features:

• 3 Piece Kit
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Is your Jeep’s steering loose? Are your tires wearing in an uneven pattern? Chances are that some of your steering components are worn. Fixing them is cheaper than replacing your tires and it’s a whole lot safer too. Omix-ADA offers high quality replaceme

Product Features:

• Includes Caps; Cups; Springs And Washers
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Is your Jeep’s oil pan gasket leaking? Or, are you rebuilding an engine and need a fresh gasket? Omix-ADA offers high-quality replacement oil pan gaskets that will give you years of service and get you back on the road.

Product Features:

• Cork
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• 8 Leaf
• Left Or Right Side
• Direct Fit
• Limited 5 Year Warranty

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• Metal
• OE Style
• Direct Fit
• Limited 5 Year Warranty

There is a big following of AMC enthusiasts that are cruising a 401 equipped Javelin or trail blazing in a rock crawling Jeep with an inline 6-cylinder! MSD offers two Pro-Billet Distributors to deliver accurate trigger signals and are maintenance-free! This pick-up never requires adjustment and simply plugs right into an MSD Ignition Control. Just above it and under our strong race rotor is an adjustable mechanical advance assembly. The chro-moly weights of this assembly slide on nylon bushings producing smooth movement of the timing. You can easily adjust the curve to match your engine’s requirements with the supplied springs and stop bushings. Each precision CNC-machined billet aluminum housing features a sealed ball-bearing and long sintered bushing for stability at any rpm and increased endurance. An oversized steel shaft receives a QPQ coating to reduce friction and prevent corrosion. Both distributors are supplied with a high quality cap, rotor and gear. There is even a vacuum advance canister for street cruising economy!

Product Features:

• Designed For Street/Performance Use w/Mech or Vacuum Advance
• Must Be Used w/An MSD Ignition Control
• Supplied w/Socket Style Distributor Cap And Rotor
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate
• Mech. advance assem. can be locked out for crank trigger systems
• Advance plate and weights are fine blanked from chrome moly steel
• QPQ coated for friction reduction

Are your Jeep’s engine gaskets leaking? Or, are you rebuilding an engine and need fresh gaskets? Omix-ADA offers high-quality replacement gaskets that will give you years of service and get you back on the road.

Product Features:

• Full Lower Gasket Set
• OE Style
• Direct Fit
• Limited 5 Year Warranty

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• With Manual Trans
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• Metal Outer Rubber Inner
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Rancho® high-performance steering stabilizers are a simple and affordable way to enhance a vehicle’s performance. Rancho® steering stabilizers are ideal for off – road driving, towing/hauling and street performance applications. Rancho® steering stabilize

Product Features:

• Black powder coated for visual appeal
• CNC cut or bent
• Steel thickness
• Direct bolt to factory steering linkage
• Designed for dual steering stabilizer

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

Is your axle’s differential making ugly noises? It could be that the pinion bearing has starved for oil or it is worn out from high mileage. The longer you wait to fix it, the more damage will be done. Omix-ADA offers new replacement pinion bearings for y

Product Features:

• Inner
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Designed by a dedicated team of Jeep enthusiasts, the ORV suspension program is one of the most complete programs available. We have looked at each application in detail to provide the very best and most complete solution for your specific Jeep model. Sin

Product Features:

• Black Powder Coated
• 4 in. Lift
• Smooth Ride
• Direct Fit
• Limited 5 Year Warranty

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• Use With 134 F-Head
• OE Style
• Direct Fit
• Limited 5 Year Warranty

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

• Gains Both Performance and Longevity
• Will Handle Any and All Torque
• Out Lasts Rubber

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

• Improved output coil for electronic ignitions
• Works w/Blaster Ignition Or MSD 5/6/7 Series
• Ballast Resistor Required If Used w/Stock Points Ignition
• Alkyd tower w/high dielectric properties lessens carbon tracking

Replace worn bushings on a Jeep® CJ5 or CJ7 with these durable Rancho® replacement leaf spring bushings. Made of high-grade polyurethane for long life, they deliver dependable performance.

Product Features:

• COMPATIBILITY — Designed for Jeep CJ5, CJ7
• REPLACES ORIGINAL HARDWARE — Replace worn bushings with these premium leaf spring bushings
• ENGINEERED TO LAST — Made of high-grade polyurethane for long service life
• EASY TO INSTALL — Kit includes eight bushings that are easy to install
• Quality part with long service life

Product Features:

• Transmission Torque Arm Grommet

Has your Jeep’s front driveshaft broken or the U-joints wore out? Can’t go off road until it’s fixed? Omix-ADA offers a wide variety of stock replacement front driveshafts. Get back on the trail to see what you’re missing.

Product Features:

• Front
• OE Style
• Direct Fit
• Limited 5 Year Warranty