International 1010 Air Intakes
Top International 1010 Air Intakes Categories
We carry over 105 Air Intakes in inventory for the International 1010. If you’re looking for aftermarket Air Intakes for your International 1010, check out all these categories:
Essential International 1010 Air Intakes
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9801)
from
$29.99
Product Features:
See More
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- STRONG AND DURABLE – Features molded rubber over an aluminized steel carrier which resists high heat and coolants
- SUPERIOR SEAL – Proprietary rubber sealing beads help eliminate potential leak paths for a superior seal
- EASIER TO INSTALL – Locating tabs assure proper alignment and easier installation
- PREVENTS OVERTIGHTENING – Torque limiters help eliminate overtightening and gasket splitting and extruding
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Holley – Prem Street Carbs (Avengers) (Part No.0-81570)
from
$671.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$17.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1922)
from
$37.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1762)
from
$24.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$60.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1927)
from
$57.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$47.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
International 1010 Air Intakes Categories
Helping You Find the Right Air Intakes for Your International 1010
You love your 1010. So we’ve made it easier than ever to help you find International 1010 Air Intakes in our online catalog. Our inventory holds 105 aftermarket and OEM Air Intakes for your International 1010, ranging from $1.99 to $1,949.99.
We offer parts from 5 brands trusted to make quality Air Intakes for your International 1010. Before you buy, take some time to read through customer reviews. We currently have 353 reviews of International 1010 Air Intakes from previous customers. Some of the top rated parts include Street Carbs with 4.0 stars and Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet with 5.0 stars.
Find your 1010 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your International 1010 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your International 1010
Our inventory holds Air Intakes for your International 1010 from 5 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, Holley, and FELPRO, all of which can keep that International happy.
We have Edelbrock parts available for your International 1010 in categories like Carburetor Parts. Some of the top-rated Edelbrock parts in these categories are:
from
$18.99
(1)
Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors
Carburetor and Injector Mount Gaskets
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
from
$16.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
Carburetor and Injector Mount Gaskets
Top-Rated Holley Air Intakes
Leading Holley Air Intakes
We carry Holley brand parts for your International 1010 across several catalog categories, including Carburetor Parts. Some of our most reviewed Holley parts include:
from
$599.99
(2)
Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate
Carburetors
FAQs for International 1010 Air Intakes
What are the most purchased Air Intakes for the International 1010?
Out of 105 Air Intakes for the International 1010, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$60.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated International 1010 Air Intakes?
Top-rated Air Intakes for your International 1010 based on customer reviews/ratings are:
from
$849.99
(2)
Street Carbs
“As you would expect from Holley this is a great carb for my 6 cyl Jeep.”
from
$799.99
(1)
Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet
“Great price on a performance carb. Will be used on a “restored” project. Holley is aLways a good choice”
