Name: Ultra Seal: Cylinder Head Bolts
Brand: Mr. Gasket
SKU: 941G
Price: 75.99 USD

from

$75.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$479.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification. Available individually and in sets of 8 or 16.

Product Features:

3/8″ Diameter, 8.280″ intake length (qt. 8), 9.250″ exhaust length (qt.8) for Big Block Chevy
One-piece .080″ wall chromemoly steel tubing
Heat-treated for extended durability and guide plate compatibility
Precision formed and reinforced pushrod end
Black-oxide finished with laser-etched part number and length

from

$113.99

Edelbrock part No. 7375 head gasket is intended for late model Gen V and VI Big Block Chevrolet engines. This gasket comes in a set.

from

$35.99

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features:

Nitrile Rubber And High Density Cork
Will Not Shrink Or Stick

from

$106.99

This Spectre engine dress-up kit was designed for the 1987 – 1995 Chevy 305 & 350 engines. This kit includes: stock height valve covers, chrome valve cover T-bolts, chrome oil filler cap, chrome PCV breather, grommets, and an air cleaner adapter stud. The air filter adapter stud, is a z-bolt that is designed to allow you to use a center stud style air cleaner assembly instead of the stock dual-stud setup. Manufactured using high quality materials this kit features triple chrome plated parts.

Product Features:

For 1987-1995 Chevrolet 305-350 engines
Includes stock height valve covers & T-bolts
Includes oil filler caps, pcv vent filter
Includes air cleaner Z-Stud
Chrome engine kit

from

$342.99

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: Street/strip applications. 10:1+ compression, 3000+ stall or 4 speed. 4.10 or lower gears and aftermarket intake. Very rough idle. OR Oval Track: Good for hobby stock in 454 where hydraulic lifters must be used.

Product Features:

Cam and lifter kit for Big Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Magnum: Street/strip applications. 10:1+ compression, 3000+ stall or 4 speed. 4.10 or lower gears and aftermarket intake. Very rough idle. OR Oval Track: Good for hobby stock in 454 where hydraulic lifters must be used.
292/292 Advertised Duration, 244/244 Duration @ .050″, .550″/.550″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$135.99

Product Features:

Use W/ Valve Springs Part #5762, 5795
Use W/ Locks Part #9612
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$32.49

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

These Are Have A Zinc Dichromate Finish
Tall Hex Head Bolt To Prevent Slippage
Extra Thick Parallel Ground Washer
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$1080.00

Product Features:

Designed for 1987-95 Throttle Body Injection or Tuned Port Injection 5.7L Small-Block Chevy engines originally equipped with center bolt valve covers
Flat Tappet Camshaft Type
60cc chambers with 165cc intake ports
Size of intake valve is 2.02 in. and exhaust valve is 1.60 in.
Sold as one complete head

from

$9.99

This is a high quality gasket that will seal that leaking water neck, and provide you with years of service. This gasket works well in all applications.

Product Features:

Made From Cellulose/Nitrile Composition
Provides Excellent Sealing And Durability
These Gaskets Are Die Cut For a Precision Fit
Fits Small Block Chevy V8 Engines 1955-’90
Fits Big Block Chevy V8 Engines 1965-’90
Fits Small Block Chrysler 318/360 1979-’92
Fits Small Block Chrysler 3.9L/5.2L/5.9L Magnum 1992-’03

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$77.99

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Grade 8 Steel

from

$18.99

Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).

Product Features:

Replacement Gasket for Top to Bottom
See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top

from

$49.99

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$159.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Non-Rotator Style: Dyno Tested and Street Proven
Great Match to Edelbrock Camshaft Kit

from

$562.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$25.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$27.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$17.79

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$512.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$223.99

VALVE SEALS, O-RING 11/32″ 1 ST

from

$27.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$32.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Made From Cellulose/nitrile Composition Material
Provides Excellent Sealing And Durability
Can Be Trimmed If Necessary For Modified Port App

from

$226.99

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

Product Features:

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.
280/280 Advertised Duration, 230/230 Duration @ .050″, .480″/.480″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$226.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.