from

$511.99

The Pro-Billet Ready-to-Run distributor is the perfect upgrade for outdated points distributors or bulky HEI. Simply install the distributor in the engine, connect three wires, the coil and fire it up! A maintenance-free magnetic pick-up accurately triggers the module. The increased output of the amplifier easily outperforms stock ignitions and will smooth out the engine’s idle, improve starting and provide a much higher RPM range. The Ready-to-Run features MSD’s adjustable mechanical advance which allows you to custom tailor an ignition curve to match your engine’s needs. There is also a vacuum advance canister to help improve economy. For positive street performance, the Ready-to-Run is the best choice.

Product Features:

Simple and clean three wire installation
Supplied w/An HEI Style Distributor Cap And Rotor
Accepts Cap-A-Dapts
Does not require an MSD Ignition Control
CARB E.O. Approved
Now includes built-in Rev Limiter
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear

from

$75.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$464.99

New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.

Product Features:

Spring Loaded Needles/Seat Increase Performance
New Qwik-Tune Adjustable Secondary Air Valve
Distinctive Black Accented Hardware
Lightweight Ball-Burnished Aluminum
No Gaskets Below Fuel Level to Prevent Leakage
Metering Rod/Step Up Springs Can Be Changed Easily
GM/AMC-Style Throttle Linkage

from

$15.79

The special self locking timing cover bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5. Application: Chevy small and big block, 1/4 inch-20 ix 1/2 inch,10 pieces.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$19.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

Designed to allow high flow rates and a consistent flow of oil to your engine
Pleated synthetic-blend filtration media removes most harmful contaminants
Fast and easy Wrench-Off removal using the welded one-inch hex nut
High capacity to withstand the service intervals recommended by vehicle manufacturers
Heavy-duty canister for outstanding durability
Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
Designed to operate with all synthetic, conventional, and blended motor oils
1-Year Limited Warranty

from

$318.99

The Mr. Gasket chrome alternator is a high-performance, remanufactured solution designed to exceed original equipment specifications, ensuring maximum dependability for your vehicle. With an 80-amp output and a sleek chrome-plated finish, this GM 10SI style alternator is both functional and visually appealing. It fits most 1973-1983 GM vehicles, making it a versatile replacement option. The alternator features a 6.6″ bolt spacing, an internal regulator for efficient voltage control, and a 1-groove V-belt pulley included for easy installation. Operating at 12 volts, it can be used as a direct OE replacement or as a 1-wire alternator, offering flexibility to suit your needs. Built for durability and reliability, this alternator is an excellent choice for restoring or upgrading your vehicle’s electrical system.

Product Features:

Fits Most 1973-1983 GM Vehicles
Bolt Spacing 6.6″
80 Amps
GM 10SI Style Alternator
Chrome Plated Finish
1-Groove V-belt pulley – included
Internal Regulator

from

$32.49

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$562.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$44.99

Product Features:

Replacement Gasket Set For PN[4242]

from

$101.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$20.49

Header Gasket Set

from

$51.99

Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.

Product Features:

Bright Ball Burnish Finish
Made From 304 Stainless
Compact Hex Head Is Ideal Where Space Is Limited
16 per Package
Resist corrosion and provides a clean professional appearance

from

$30.49

Product Features:

Transfer Case Torque Mount

from

$483.99

The Hurst Quarter Stick is designed for 2 and 3 speed applications. Its precision gate style mechanism ensures a positive feel. It features, a neutral safety switch, NHRA approved reverse lockout, and a brushed aluminum cover.

Product Features:

Forward and Reverse Shift Patterns
Chrome Plated Trigger for Detent Activity
Factory Neutral Safety Switch
Compact And Lightweight
Roller Detent with Shifter Pattern

from

$251.99

HYDRAULIC – Xtreme Energy: Great for street machines, largest cam for stock converter, better with 2000 stall.

Product Features:

HYDRAULIC – Xtreme Energy: Great for street machines, largest cam for stock converter, better with 2000 stall.
268/280 Advertised Duration, 224/230 Duration @ .050″, .477″/.480″ Lift, 110 Lobe Separation
Valve spring upgrade required
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$127.99

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

Automatic Transmission Dip Stick
Mounts to bellhousing
Sold as a kit
Natural finish
Fits TH350 & TH350C

from

$423.99

Edelbrock #88503 Water Pump big block Chevy short black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pu

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.750 in. Block To Hub Height
Black Finish

from

$511.99

Power Train

from

$83.99

COMP Cams Hi-Tech Roller Race Timing Sets include cast iron camshafts gears, induction hardened billet steel crank sprockets, and pre-stretched, heat-treated double roller chains with heavy-duty large pin design. They feature 3 keyway crank sprockets for

Product Features:

Cast iron camshaft gear and induction hardened billet steel crank sprocket
Pre-stretched, heat-treated true double roller chain with heavy-duty large pin design; chain available separately
Ideal for all street performance and race applications
Features 3 keyway crank sprocket for 4-degree incremental adjustability, 4-degree maximum advance/retard
Dynamically balanced and quality checked for run-out tolerances

from

$25.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$55.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$13.99

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

from

$116.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features: