GMC K15/K1500 Pickup Performance Engines

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

• Cylinder Head Bolts
• Longer-Than-Stock
• High Quality Grade 8 Alloy
• Increase Torque Settings
• Higher Clamp Loads On Gasket

Product Features:

• 4.125 in. Cylinder Bore Diameter
• 0.039 in. Thickness
• 8.7cc Volume
• Charcoal Color
• Two Piece Configuration

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 8″ diameter
• 1970-73, 396-427-454 cu. in.
• 1967-69, 302 cu. in.
• 1965-68, 327 cu. in. hi-performance
• 1970-76, 400 cu. in.
• 1970-73, 350 cu. in.

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:

• Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
• Features a tough, scuff-resistant silicone rubber coating
• Helps in sealing without the engine warming up
• Reduces fluid migration through the gasket
• Resists fatigue

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Silicone beading on both sides of each gasket
• Complete with manifold end seals and distributor gasket
• For OE replacement, high performance street, drag race and oval track use
• Creates Tight Leak proof Seal

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retains good throttle response and acceleration. Larger plenum and runners maximize other upgrades. Edelbrock total power package maximizes gains. Available in cast, polished or endurashine finish.

Product Features:

• Based on Performer RPM-Series with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• Designed for 1500 to 6500 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades
• Edelbrock Total Power Package Maximizes Gains

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

• Cam and lifter kit for Big Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
• 295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
• Valve spring upgrade required

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.

Product Features:

• Features Nitrile Rubber Material For Long Life
• Molded Rubber Gaskets Are Reusable
• Ideal For Engine Requiring Valve Lash Maintenance

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

The Edelbrock #609019 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only