GMC K15/K1500 Pickup Ignition and Tune-Up Products

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

Product Features:

• CARQUEST Ignition Modules creates and refines the timing of the engine using various sensors and readings throughout the spark system in order to create an efficiently running engine.
• CARQUEST Ignition Modules use current and voltage limiting circuitry in order to prevent the ignition coil from over voltage/current. Over voltages can allow for coils to create excessive heat which can damage to the ignition module resulting in check eng
• CARQUEST Ignition Modules are 100% individually tested for all product functionalities including over voltage, timing and dwell.

Distributors

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.

Product Features:

• Rolled Edges For Strength
• Ideal For Magnetos
• Ideal For Ignition Distributor

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

Most modern electronic ignition systems require suppression style wires to preserve sensitive components. Flame-Thrower 8mm Custom fit MAGx2 wires provide enhanced RFI suppression and dual current paths for more power delivered to the spark plug. Our custom wire sets have factory terminated ends for a superior connection and perfect fit, without cutting, crimping and splicing.

Product Features:

• Two current paths for reliability and redundancy. -Primary path: Spiral wound stainless steel alloy.-Secondary path: Carbon impregnated fiberglass center core.
• Low 500 ohm per foot resistance.
• 8mm Silicone jacket to resist high temperatures, moisture, oil and chemicals.
• EPDM (Ethylene Propylene Diene Methylene) inner insulation for superior heat resistance and prevention of arcing and voltage leaks.
• Fiberglass reinforcing braid for added strength and flexibility.

Carquest ignition coils meet original equipment (OE) fit, form and function and are built to ensure reliable starting and performance. Carquest ignition coils are tested to ensure proper spark and perfect fit for each application. These ignition coils are an affordable repair choice to restore the vehicle’s ignition system performance. Carquest ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Long service life and durable performance
• High dielectric strength for reliability
• Corrosion-resistant connections
• Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413
• High reliability
• Long service life

Set includes terminals for engines with early type (socket) and late type (HEI spark plug top) distributor caps. 90 degree boots and terminals factory installed on one end.

Product Features:

• Extra Long 8.5mm Wires So You Can Cut To Your Designed Length
• Incl. both socket-style and spark plug-style boots and terminals
• Includes Mini-Stripper-Crimper For Factory Style Crimps
• Size Includes: [2]48/50/56 in./[3] 32 in. Wires/Boots/Terminals
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

Black; 7in. Small Bl

Edelbrock part No. 22737 is a bronze alloy drive gear for use on ProFlo EFI & Max-Fire distributor in small-block & big-block Chevrolet engines.

Our Chevrolet front drive distributors brought the need for a distributor plug. Both are billet aluminum and feature a slip collar to ensure correct installation depth.

Product Features:

• Use On Engines w/Wet Sump Oil System And Front Drive Dist.
• Supplied w/Bronze Gear
• Must Be Used w/An MSD Crank Trigger
• Adj. slip collar mounting flange for engines w/modified deck hts.
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Oversized Polished Steel Shaft w/QPQ Coating

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Fel-Pro Oil Pan SnapUps 8mm bolts
• Designed to hold up the pan and gasket, for one person installation
• Engine$aver Hardware
• Unsurpassed quality you can trust
• Sold in sets of four and are reusable

This spark plug non fouler is designed for easy installation on specified vehicles to protect spark plugs from fouling and damage. It is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this spark plug non fouler is designed for easy installation to protect spark plugs from fouling and damage on specified vehicles
• Ideal solution – this non-fouler preserves spark plug life and is a reliable replacement for an original non-fouler that has failed due to corrosion
• Durable construction – made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

BWD SELECT designs, specifies, and manufactures replacement parts with one goal in mind-make them the very best. To maximize performance and longevity, we use the finest materials and improve on OE specifications, whenever possible.

Product Features:

• High-quality direct replacement electrical connector allows you to replace only the damaged connector instead of the entire harness for a cost-effective repair
• The terminal is manufactured with high grade materials such as copper alloy, brass, and phosphor bronze.  The housing is fabricated using polyamide resins.  All of the materials together provide the connectors with prolonged life and superior performance.
• All electrical connectors are 100% tested for proper mechanical and electrical fit, form and function
• Offering thousands of high-quality pigtails & sockets for nearly every electrical job

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

• Adjustable Vacuum Advance
• Increases Horsepower And Throttle Response
• Includes Allen Wrench For Adjustments
• Instantly Increase Horsepower
• Maximum Possible Spark Advance
• Not Legal For Sale/Use In CA

New Goodmark Ignition Switch Nut

Product Features:

• Made Of Die Cast
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

SYLVANIA Long Life miniature bulbs provide standard performance for your car or truck’s interior and exterior auxiliary lighting. Ideal for use in your car’s back up/reverse, trunk, dome lights and more, Long Life bulbs are a direct replacement for your vehicle. Designed for durability, lower maintenance, and safety in mind.

Product Features:

• DEPENDABLE: Made from high quality materials for long-lasting durability
• EASY DIY INSTALLATION: A direct replacement for the factory bulbs in your vehicle, no modification required
• SMART MAINTENANCE: Always replace bulbs in pairs to ensure equal brightness and color
• PRO TIP: When changing your bulb, never touch the glass. Always use gloves or a clean shop towel to reduce the transfer of oils during install
• SAFETY: High-quality SYLVANIA bulbs are designed to perform to all relevant safety standards set for the lighting application
• TRUSTED BRAND: SYLVANIA is a trusted OEM automotive lighting manufacturer, with over 100 years of superior optical engineering experience

Iridium Power Spark Plug delivers unmatched performance with the world’s smallest iridium center electrode at just 0.4mm, ensuring maximum spark energy for superior combustion. Engineered with patented 360-degree laser welding and a U-groove taper cut ground electrode, it optimizes flame propagation for enhanced engine efficiency. Built to withstand extreme temperatures exceeding 4000 Deg F, its burnished nickel plating offers exceptional resistance to corrosion and high-temperature endurance. Designed for a wide range of applications, including classic and collector cars, this spark plug provides superior horsepower and fuel efficiency while requiring 5,000 volts less to fire compared to conventional plugs. Its durable iridium material and flat seat type ensure long-lasting reliability, while enhanced engine starts reduce misfires even under heavy loads. Experience the pinnacle of spark plug technology with Iridium Power for maximum performance and efficiency.

Product Features:

• World’s smallest Iridium Center Electrode (0.4mm) for improved spark for maximum combustion
• Patented 360-degree laser welding assembly process
• U-groove and taper cut ground electrode to maximize flame propagation.
• Withstands temperatures greater than 4000 degree Fahrenheit
• Burnished nickel plating for high temperature endurance and superior corrosion resistance
• Wide range of part numbers for thousands of applications, including classic and collector cars
• Iridium Power
• Superior Performance: Patented technology allows the Iridium Power plug to outperform any other spark plug, delivering more horsepower and better fuel efficiency.
• Low Voltage Requirement: Requires 5,000 volts less to fire compared to conventional spark plugs, making it highly efficient and reliable under extreme conditions.
• Enhanced Engine Starts: Provides faster and easier starts, reducing the likelihood of misfires even under heavy loads.
• Durable Iridium Material: Constructed with a durable iridium center electrode tip and a flat seat type, ensuring long-lasting performance and reliability.

An Ignition Capacitor is a device that will absorb excessive voltage spikes in electrical systems. The typical location or use for a capacitor is inside a distributor tied into a point ignition system. The ignition capacitor may also be called a radio capacitor or condenser used in electrical devices which may be susceptible to voltage spikes.

Product Features:

• Application matched component to ensure the system can be returned to like new condition.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Premium Vehicle Solutions provides high-quality solutions for a wide range of applications. The Ignition Switch allows for reliable control of the vehicle’s electrical systems and engine start-up, enhancing convenience and ensuring consistent performance during operation. Engineered for maximum performance and durability, our products are built to excel in even the most demanding conditions, ensuring reliable operation and long-lasting value.

Product Features:

• Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
• Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
• Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
• Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

ACCEL now offers the cure for burnt spark plug boots with Extreme 9000 ceramic wire kits. The 8mm Ferro-Spiral core wire now has ceramic boots on the spark plug end of the wires. Ceramic boots withstand up to 2,000 degrees. Great for running headers with close tolerance, an engine bay with little room, or an RV with boots that melt because of heat. Ultra high temperature double silicone construction wire rated at 600 degrees Fahrenheit peak. 500 ohms/ft Ferro-Spiral core developed for performance use. Excellent energy delivery to the spark plugs, while providing the highest level of RFI/EMI suppression. Stainless steel spark plug terminals for maximum spark energy to the plugs. Pre-made to factory lengths for a perfect fit.

Product Features:

• Ceramic boots withstand up to 2,000░ Fahrenheit
• Ceramic boots withstand up to 2,000° Fahrenheit
• 8mm double silicone construction black wire rated at 600░ F rated
• 8mm double silicone construction black wire rated at 600° F rated
• 500 Ohms/foot ferro sprial core offers the highest level of RFI/EMI suppression
• Universal and custom fit applications
• Universal And Custom Fit Applications