GMC K15 Performance Fuel Systems

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.

Not only does the Sniper EFI 2GC offer superior throttle response and WOT power over the carburetor, but you may also benefit from increased fuel economy! Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking EFI to the next level.

Make your classic drive like a modern fuel injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

The 1 EFI conversion system just got better! Introducing Sniper 2 EFI – a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. We took everything that we learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more.

Not only does the Sniper EFI 2GC offer superior throttle response and WOT power over the carburetor, but you may also benefit from increased fuel economy! Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking EFI to the next level. The Sniper EFI 2GC system is capable of supporting 350 HP on naturally aspirated engines. Upgrade to Sniper EFI today!.

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.

If you’re looking to make some big power, the Super Sniper Stealth is made for you! Holley’s Sniper EFI Super Sniper Stealth 1250 is the best way to convert your carbureted engine to fuel injection with just 4 simple connections required. Super Sniper can support up to 1250HP boosted with 8 100 LB/HR Injectors. With a Stealth 1250 system, you get that carburetor styling but the functionality of a Sniper! This 4-barrel system features a single pattern bolt on design built to fit 4150 flange manifolds. The Super Sniper Stealth ECU is capable of fuel map self-learning and ignition timing control, improving idle stability, drivability, and wide-open throttle horsepower. Additionally, this Sniper kit also includes transmission kick down provisions for GM TH350/400, 200R4/700R4, and Ford C4/C6 applications!.

Edelbrock Performer RPM Series fuel pump for SBC and W Series Chevy, 1721.

Precision cut to cover stock fuel pump opening when converting to an electric fuel pump. Gasket included.

Edelbrock Performer RPM Series fuel pump is for Big-Block Chevrolet, 1722.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

“The Edelbrock AVS2 Series #1906 is a satin-finished four-barrel carburetor with electric choke that is designed and calibrated for optimum street performance in engines that require an air-fuel flow of 650 CFM. The AVS2 is a perfect replacement or upgrade that features annular flow primary boosters with a new calibration for improved off-idle and cruising performance. The annular flow booster design delivers improved fuel atomization to eliminate flat spots that may be encountered as the carburetor transitions from idle to full throttle. Each annular flow booster features eight equally spaced orifices to improve fuel metering from idle to the main circuit. The improved flow metering makes this carburetor ideal for use with a wide variety of small- and big-block engines with either dual- or single-plane intake manifolds. The Edelbrock AVS2 #1906 includes both timed and full vacuum ports for ignition advance. It comes with: .101 primary and.098 secondary metering jets; .070 x .037 metering rods; orange (5″” Hg) step-up spring. Use our Carburetor Stud Kits #8008 or #8024 if needed. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, RPM Air-Gap, Performer RPM, Torker II or other brands of similar design. For a black-finished AVS2 with electric choke, order part #19063.”

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!

Each calibration has been dyno and track tested to deliver proven performance!

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

“The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “”hold a tune””, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.”

Holley Double Pumper(R) carburetors are a perfect performance upgrade for hot street cars and race vehicles. Double Pumper carburetors are an American icon when it comes to performance carburetors. From their roots as the premier carburetor on many factory muscle cars to powering thousands of vehicles across the finish line, the Double Pumper is a great choice whether you are burning up the street or the quarter mile.

Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!

Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.