GMC K15 Indy Hauler Air Intakes
Top GMC K15 Indy Hauler Air Intakes Categories
We carry over 148 Air Intakes in inventory for the GMC K15 Indy Hauler. If you’re looking for aftermarket Air Intakes for your GMC K15 Indy Hauler, check out all these categories:
Essential GMC K15 Indy Hauler Air Intakes
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1828)
from
$28.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Performer RPM Small Block Chevy Intake Manifold (Part No.7101)
from
$296.99Product Features:
- Best for the Ultimate in Street High-Performance
- Designed for 1500 to 6550 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
- Edelbrock Total Power Package Maximizes Gains
- Also in Polished/PermaStar/EnduraShine Finish
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1099)
from
$44.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Holley – Professional Race Carburetor: 1150 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80906HB)
from
$1899.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Mr. Gasket – Intake Bolt Kit (Part No.5003)
from
$87.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.
Product Features:
See More
Product Features:
- Chrome plated
- Grade 8
- 12-point head
- AN washers with no exposed shoulder for a professional appearance
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$56.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$50.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Mr. Gasket – Ultra-Seal Intake Manifold Gasket with Silicone Beading (Part No.5821)
from
$34.99
Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For original equipment replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90314-3)
from
$22.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES – Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE – Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Edelbrock – Intake Manifold replacement base to top gasket (Part No.6999)
from
$18.99
Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).
Product Features:
See More
Product Features:
- Replacement Gasket for Top to Bottom
- See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$17.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
GMC K15 Indy Hauler Air Intakes Categories
Helping You Find the Right Air Intakes for Your GMC K15 Indy Hauler
You love your K15 Indy Hauler. So we’ve made it easier than ever to help you find GMC K15 Indy Hauler Air Intakes in our online catalog. Our inventory holds 148 aftermarket and OEM Air Intakes for your GMC K15 Indy Hauler, ranging from $4.29 to $1,972.99.
We offer parts from 9 brands trusted to make quality Air Intakes for your GMC K15 Indy Hauler. Before you buy, take some time to read through customer reviews. We currently have 450 reviews of GMC K15 Indy Hauler Air Intakes from previous customers. Some of the top rated parts include Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Street Carbs with 3.4 stars.
Find your K15 Indy Hauler Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC K15 Indy Hauler part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your GMC K15 Indy Hauler
Our inventory holds Air Intakes for your GMC K15 Indy Hauler from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, FELPRO, and Mr. Gasket, all of which can keep that GMC happy.
We have Felpro parts available for your GMC K15 Indy Hauler in categories like Carburetor Parts and Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your GMC K15 Indy Hauler across several catalog categories, including Carburetor Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Carburetors
from
$50.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
FAQs for GMC K15 Indy Hauler Air Intakes
What are the most purchased Air Intakes for the GMC K15 Indy Hauler?
Out of 148 Air Intakes for the GMC K15 Indy Hauler, the most popular in our inventory are:
from
$34.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Intake Manifold Gasket Sets
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated GMC K15 Indy Hauler Air Intakes?
Top-rated Air Intakes for your GMC K15 Indy Hauler based on customer reviews/ratings are:
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
