GMC C35 Air Intakes
Top GMC C35 Air Intakes Categories
We carry over 193 Air Intakes in inventory for the GMC C35. If you’re looking for aftermarket Air Intakes for your GMC C35, check out all these categories:
Essential GMC C35 Air Intakes
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1741)
from
$22.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Edelbrock – Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port (Part No.7208)
from
$32.99
Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an
Product Features:
See More
Product Features:
- 1.82″x2.46″
- Rectangular Port Style
- .060″ Thick
- Two Piece Configuration
- Composite Material
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1044)
from
$39.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$196.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$36.99
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Felpro – Carburetor Choke Tube Gasket (Part No.72591)
from
$4.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
United Carb – Remanufactured Carburetor 4 Barrel (Part No.3-3592)
from
$289.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Performer RPM AIR-Gap Small Block Chevy Dual-Quad Intake Manifold (Part No.7525)
from
$509.99
Air gap cooler and denser mixture for more power. Street and high performance compatible. Available in cast, polished and endurashine finish.
Product Features:
See More
Product Features:
- Based on C26 Low Profile with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- 1.625 in. Taller Than Low-Profile PN[5425]
- Also Available In EnduraShine Finish PN[75254]
- Also Available As Complete Kit PN[2025/20254]
- Best When Matched with Edelbrock 500cfm Carburetor
- Use Fuel Line Kit PN[8088/8091]
- Use Progressive Throttle Linkage Kit PN[7094]
Edelbrock – Performer Small-Block Chevy Intake Manifold for Street Performance (Part No.3701)
from
$356.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes and Accepts EGR
Felpro – Carburetor Mounting Gasket (Part No.60249)
from
$7.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$50.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
GMC C35 Air Intakes Categories
Helping You Find the Right Air Intakes for Your GMC C35
You love your C35. So we’ve made it easier than ever to help you find GMC C35 Air Intakes in our online catalog. Our inventory holds 193 aftermarket and OEM Air Intakes for your GMC C35, ranging from $4.29 to $1,972.99.
We offer parts from 9 brands trusted to make quality Air Intakes for your GMC C35. Before you buy, take some time to read through customer reviews. We currently have 2,757 reviews of GMC C35 Air Intakes from previous customers. Some of the top rated parts include Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.6 stars and Intake Manifold Bolts with 4.2 stars.
Find your C35 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC C35 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your GMC C35
Our inventory holds Air Intakes for your GMC C35 from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Mr. Gasket, all of which can keep that GMC happy.
We have Felpro parts available for your GMC C35 in categories like Carburetor Parts and Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your GMC C35 across several catalog categories, including Intake Manifold Parts. Some of our most reviewed Felpro parts include:
FAQs for GMC C35 Air Intakes
What are the most purchased Air Intakes for the GMC C35?
Out of 193 Air Intakes for the GMC C35, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$34.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Intake Manifold Gasket Sets
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
What are the top-rated GMC C35 Air Intakes?
Top-rated Air Intakes for your GMC C35 based on customer reviews/ratings are:
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
