GMC C15/C1500 Pickup Air Intakes
Top GMC C15/C1500 Pickup Air Intakes Categories
We carry over 230 Air Intakes in inventory for the GMC C15/C1500 Pickup. If you’re looking for aftermarket Air Intakes for your GMC C15/C1500 Pickup, check out all these categories:
Essential GMC C15/C1500 Pickup Air Intakes
Edelbrock – Standard Main Jet Carburetor Metering Jet #12458 Size .057 (Pair) (Part No.12458)
from
$14.99
The Edelbrock 94 #12458 Carburetor Jets .058″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 58 Maximum Jet Size
- 0.057 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$56.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1819)
from
$18.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Dorman – Help – Throttle Return Spring (Part No.59209)
from
$10.49
This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$17.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Felpro – Carburetor Mounting Gasket (Part No.9249)
from
$1.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Holley – Professional Race Carburetor: 950 CFM, No Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80901RD)
from
$1599.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1099)
from
$44.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Performer RPM Small Block Chevy AIR-Gap Intake Manifold (Part No.7501)
from
$374.99
Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Dual-plane high-rise intake. For square bore carburetors only. For street and high performance use. Available in cast, polished or endurashine finish.
Product Features:
See More
Product Features:
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake
- For Square Bore Carburetors Only
Mr. Gasket – Ultra-Seal Intake Manifold Gasket with Silicone Beading (Part No.5821)
from
$34.99
Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For original equipment replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$196.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Felpro – Air Cleaner Mounting Gasket (Part No.11528)
from
$2.49
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
GMC C15/C1500 Pickup Air Intakes Categories
Helping You Find the Right Air Intakes for Your GMC C15/C1500 Pickup
You love your C15/C1500 Pickup. So we’ve made it easier than ever to help you find GMC C15/C1500 Pickup Air Intakes in our online catalog. Our inventory holds 230 aftermarket and OEM Air Intakes for your GMC C15/C1500 Pickup, ranging from $1.99 to $1,972.99.
We offer parts from 9 brands trusted to make quality Air Intakes for your GMC C15/C1500 Pickup. Before you buy, take some time to read through customer reviews. We currently have 7,280 reviews of GMC C15/C1500 Pickup Air Intakes from previous customers. Some of the top rated parts include Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.6 stars and Intake Manifold Bolts with 4.2 stars.
Find your C15/C1500 Pickup Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC C15/C1500 Pickup part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your GMC C15/C1500 Pickup
Our inventory holds Air Intakes for your GMC C15/C1500 Pickup from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Mr. Gasket, all of which can keep that GMC happy.
We have Felpro parts available for your GMC C15/C1500 Pickup in categories like Carburetor Parts and Air Cleaner Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your GMC C15/C1500 Pickup across several catalog categories, including Intake Manifold Parts. Some of our most reviewed Felpro parts include:
FAQs for GMC C15/C1500 Pickup Air Intakes
What are the most purchased Air Intakes for the GMC C15/C1500 Pickup?
Out of 230 Air Intakes for the GMC C15/C1500 Pickup, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$34.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Intake Manifold Gasket Sets
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
What are the top-rated GMC C15/C1500 Pickup Air Intakes?
Top-rated Air Intakes for your GMC C15/C1500 Pickup based on customer reviews/ratings are:
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
