GMC B7 Belts and Hoses

Essential GMC B7 Belts and Hoses

Gates – FleetRunner« Heavy-Duty Micro-V« Serpentine Drive Belt (Part No.K070705HD)

FleetRunner« Heavy-Duty Micro-V« Serpentine Drive Belt

from

$57.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.

Product Features:
  • Patented material provides peak performance at prolonged extreme operating temperatures
  • Heavy-duty construction resists cracking and wear, even at extreme temperatures
  • Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
  • Problem solver designed for the toughest applications
  • Consistently outperforms other heavy-duty serpentine belts on the market
  • Engineered to save your fleet money and reduce downtime
  • Tensioner Replacement is Recommended (if equipped)
See More

Dayco – Poly Rib Belt Serpentine Belt; 70.5 Long, 7 Rib Count (Part No.5070705)

Poly Rib Belt Serpentine Belt; 70.5 Long, 7 Rib Count

from

$34.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Litens – Accessory Drive Belt Tensioner – Original Equipment Quality (Part No.910010A)

Accessory Drive Belt Tensioner - Original Equipment Quality

from

$196.99
This Heavy Duty Truck and Bus tensioner is designed and engineered by one of world’s largest supplier of original equipment (O.E.) belt tensioners in the world. The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part. This part is manufactured to meet or exceed the performance and life specifications of the O.E. part. The part features a premium chrome-silicon steel spring, internal damping, a “lift-lug” feature for ease of installation, Tandem 6303 ball bearings, a molded locator pin for precise installation, and a forged steel pulley. Specifically designed for a wide variety of Medium/Heavy Duty Trucks, Buses, Road and Construction Equipment, and Farm Equipment. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Product Features:
  • Manufactured by one of the world’s largest Original Equipment suppliers of accessory drive tensioners and pulleys.
  • Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
  • Heavy Duty Electro-deposited coated (e-coat) Steel Pulley for superior corrosion resistance.
  • Professional Mechanics will change this tensioner in approx. 1/2 hour
  • Accessory drive belts and tensioners are manufactured with similar design life targets. Since belt removal is required to change the tensioner, replacing both will extend the system service life and lower labor costs versus individual replacement.
  • Belt removal is required to change the tensioner. Therefore, doing both together will extend accessory drive life and lower overall labor versus performing these services separately.
  • Installation instructions included.
See More

Gates – FleetRunner½ Heavy-Duty Automatic Belt Drive Tensioner (Part No.38507)

FleetRunner½ Heavy-Duty Automatic Belt Drive Tensioner

from

$223.99
Product Features:
  • Optimized components engineered for maximum strength and durability
  • Patented design provides superior belt alignment and tension for improved drive efficiency and life
  • Patented labyrinth seal prevents contamination of internal parts for maximum durability and service life
  • Long-lasting steel pulleys with dust shields to protect internal bearings from contamination
  • Double row bearings carry more load and last up to 3X longer than two individual bearings
  • Chrome-silicone round torsion spring for less +ex-fatigue than +at-spring designs
  • Patented damping mechanism provides maximum stability, reducing vibration and increasing the life of the belt, tensioner and other accessory drive components
See More

Dayco – Bottom Cog V-Belt; 69 Inch Long, Exact Fit Premium Quality (Part No.17690)

Bottom Cog V-Belt; 69 Inch Long, Exact Fit Premium Quality

from

$25.99
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.

Product Features:
  •  Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
  •  Provides greater durability and flexibility – 35% stronger than all previous versions
  •  Features specially treated cords for added strength, stability and reliability
  • Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
See More

Driveworks – Automotive V-Belt (Part No.34017)

Automotive V-Belt

from

$5.19
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.

Product Features:
  • This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
  • Polyester cords provide extreme tension-holding capability for longer belt life
  • The raw edge belt design delivers the maximum gripping power
  • The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
See More

Dayco – V-Belt, Top Cog (Part No.17525)

V-Belt, Top Cog

from

$27.49
Dayco® High Performance V-Belt is the workhorse of the heavy-duty industry. Polyester cord provides maximum power transfer and tension holding capability for the life of the belt. The laminated construction helps absorb greater shock loads associated with diesel engines. These Dayco® High Performance V-Belt advantages translate into less downtime, lower maintenance costs, and increased dependability. Dayco’s High Performance V-Belt meets or exceeds SAE J636 and J637 specifications.

Product Features:
  • The High Performance V-Belt design delivers more flexibility and increases airflow around the belt, so it runs cooler and lasts longer than most competitive belts
  • Polyester cord provides maximum power transfer and tension holding capability for the life of the belt
  • The laminated construction helps absorb greater shock loads associated with diesel engines
  • Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$87.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

Gates – Premium Molded Coolant Hose (Part No.22663)

Premium Molded Coolant Hose

from

$76.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Coolant Hose (Part No.22136)

Premium Molded Coolant Hose

from

$175.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 25.50" Long, 2" Diameter (Part No.E70770)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 25.50" Long, 2" Diameter

from

$25.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Premium Molded Coolant Hose (Part No.22135)

Premium Molded Coolant Hose

from

$213.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38033)

DriveAlign½ Belt Drive Idler/Tensioner Pulley

from

$47.99
Product Features:
  • Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
  • Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
  • OE-quality fit for virtually every domestic or import vehicle on the road today
  • Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
  • Premium bearings eliminate bearing noise
  • Mounting hardware included for some popular applications
  • Reliable operation under severe conditions
See More

Dayco No Slack Gold Label – Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 32.8mm Width, Smooth (Part No.89105)

Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 32.8mm Width, Smooth

from

$45.99
Designed to replace idler and tensioner pulleys for serpentine drives in heavy-duty diesel engine applications, Dayco HD idler/tensioner pulleys are machined from high-strength steel or powdered metal material to provide excellent wear resistance under harsh environments. Dual pressed-in bearings provide long bearing life and protection against the shock loads experienced by today’s diesel trucks.

Product Features:
  • Engineered for the demanding drive systems of today’s class 4-8 heavy-duty commercial trucks
  • Premium OE technology to ensure peak performance under extreme conditions
  • Utilizes 3D dimensional computer aided design (CAD) and finite element analysis (FEA) for optimal design and maximum structural integrity
  • Meets or exceeds OE quality
See More

Litens – Idler/Tensioner Pulley: Direct Fit, Steel, 90mm Diameter (Part No.900045A)

Idler/Tensioner Pulley: Direct Fit, Steel, 90mm Diameter

from

$51.99
This pulley is supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, specifications and meets performance and durability requirements. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Product Features:
  • Heavy Duty steel pulley with a long lasting automotive bearing.
  • Precision steel stamping with close tolerance ball bearing pocket.
  • Electro-deposited coating (e-coat) for superior corrosion resistance.
  • Running surface designed and engineered for proper belt tracking.
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18" Long, 1.75" Diameter (Part No.E72158)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18" Long, 1.75" Diameter

from

$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 2.25" Diameter (Part No.E71565)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 2.25" Diameter

from

$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Helping You Find the Right Belts and Hoses for Your GMC B7

You love your B7. So we’ve made it easier than ever to help you find GMC B7 Belts and Hoses in our online catalog. Our inventory holds 67 aftermarket and OEM Belts and Hoses for your GMC B7, ranging from $1.99 to $223.99.

We offer parts from 6 brands trusted to make quality Belts and Hoses for your GMC B7. Before you buy, take some time to read through customer reviews. We currently have 326 reviews of GMC B7 Belts and Hoses from previous customers. Some of the top rated parts include Poly Rib Belt Serpentine Belt; 67 Long, 6 Rib Count with 4.7 stars and Automotive V-Belt with 5.0 stars.

Find your B7 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC B7 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Belts and Hoses Brands for Your GMC B7

Our inventory holds Belts and Hoses for your GMC B7 from 6 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Driveworks, and Litens, all of which can keep that GMC happy.

Top-Rated Dayco Belts and Hoses

Leading Dayco Belts and Hoses

We carry Dayco brand parts for your GMC B7 across several catalog categories, including Serpentine and V Belts. Some of our most reviewed Dayco parts include:
Poly Rib Belt Serpentine Belt; 67 Long, 6 Rib Count
from $33.49
(5)
Poly Rib Belt Serpentine Belt; 67 Long, 6 Rib Count
Serpentine Belts

FAQs for GMC B7 Belts and Hoses

What are the most purchased Belts and Hoses for the GMC B7?

Out of 67 Belts and Hoses for the GMC B7, the most popular in our inventory are:
Poly Rib Belt Serpentine Belt; 66 Long, 6 Rib Count
from $28.99
(3)
Poly Rib Belt Serpentine Belt; 66 Long, 6 Rib Count
Serpentine Belts

What are the top-rated GMC B7 Belts and Hoses?

Top-rated Belts and Hoses for your GMC B7 based on customer reviews/ratings are:
Poly Rib Belt Serpentine Belt; 67 Long, 6 Rib Count
from $20.99
(3)
Poly Rib Belt Serpentine Belt; 67 Long, 6 Rib Count
“Great parts at a great price”
Automotive V-Belt
from $5.19
(1)
Automotive V-Belt
“God”
Automotive RPF Raw Edge Cogged Belt
from $24.49
(1)
Automotive RPF Raw Edge Cogged Belt
“Also known as Dayco Upgrades. Still going strong on my ’84 Toyota Supra. However my alternator is acting erratic going from 10 volts up to 18 volts. I”