GMC 150 Air Intakes
Top GMC 150 Air Intakes Categories
We carry over 30 Air Intakes in inventory for the GMC 150. If you’re looking for aftermarket Air Intakes for your GMC 150, check out all these categories:
Essential GMC 150 Air Intakes
Edelbrock – Pro-Flo XT Small Block Chevy EFI Black Intake Manifold (Part No.71373)
from
$746.99
Edelbrock part #71373 Pro-Flo XT intake manifold is designed for 1957-86 small-block Chevy V8 applications. The Pro-Flo XT intakes are engineered with a large plenum and long tapered runners to deliver maximum horsepower and broad torque throughout the rp
Product Features:
See More
Product Features:
- 1500-7000 RPM Range
- Single Plane Type-Throttle Body XT Style Flange
- 9 in. Front Height, 9 in. Center Height, 8.2 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Edelbrock – Performer RPM AIR-Gap Small Block Chevy Polished Intake Manifold (Part No.75011)
from
$749.99
Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Dual-plane high-rise intake. For square bore carburetors only. For street and high performance use. Available in cast, polished or endurashine finish.
Product Features:
See More
Product Features:
- Polished Version Of Edelbrock PN[7501]
- Polish is Hand-Buffed for Brilliant Shine
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock – Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish (Part No.27033)
from
$468.99
Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
- Black Powder Coated Finish
- Non-EGR W/ Oil Fill Tube
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$196.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$56.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)
from
$60.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-4412S)
from
$534.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to push you to the finish line on Saturday night, the Holley 0-4412 Performance 2BBL is the perfect choice.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carburetor: 500 CFM, Electric Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-80500)
from
$599.99
Street Avenger carburetors are known to bolt on right out of the box and Holley is excited to announce the addition of our new 2bbl Street Avenger models available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations; three vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included 3/8″ fuel line connection so there are no unnecessary trips back to the parts store.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Built In No Trouble Fuel Inlet Filter
- Provides Precise Fuel Control For Low End Torque/Acceleration
- Gen Iv No Trouble Power Valve
- Three Vacuum Ports [1 Pcv/Brake 1 Timed Spark 1 Full]
- Limited Lifetime Warranty Defects In Material/Workmanship
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412CT)
from
$649.99
Competition fuel curves provide safe and reliable horsepower for high performance race engines.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Gold Dichromate (Part No.0-4412C)
from
$649.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Felpro – Carburetor Mounting Gasket (Part No.9093)
from
$3.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9334 SH)
from
$24.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9498 SH-1)
from
$24.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9257 SH)
from
$22.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
GMC 150 Air Intakes Categories
Helping You Find the Right Air Intakes for Your GMC 150
You love your 150. So we’ve made it easier than ever to help you find GMC 150 Air Intakes in our online catalog. Our inventory holds 30 aftermarket and OEM Air Intakes for your GMC 150, ranging from $3.49 to $1,865.99.
We offer parts from 4 brands trusted to make quality Air Intakes for your GMC 150. Before you buy, take some time to read through customer reviews. We currently have 11 reviews of GMC 150 Air Intakes from previous customers.
Find your 150 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC 150 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your GMC 150
Our inventory holds Air Intakes for your GMC 150 from 4 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, Holley, and FELPRO, all of which can keep that GMC happy.
We have Edelbrock parts available for your GMC 150 in categories like Intake Manifold Parts. Some of the top-rated Edelbrock parts in these categories are:
FAQs for GMC 150 Air Intakes
What are the most purchased Air Intakes for the GMC 150?
Out of 30 Air Intakes for the GMC 150, the most popular in our inventory are:
from
$374.99
This product is not rated
Performer RPM Small Block Chevy AIR-Gap Intake Manifold
Intake Manifolds
from
$356.99
This product is not rated
Performer Small-Block Chevy Intake Manifold for Street Performance
Intake Manifolds
from
$296.99
This product is not rated
Performer RPM Small Block Chevy Intake Manifold
Intake Manifolds
