Excalibur Phaeton Camshafts

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: Street/strip special, 3000 stall, headers, gears, 9.5:1+ compression. Very rough idle. OR Drag Race: 3000+ stall in heavy car with 10:1+ compression.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Magnum: High performance. Biggest cam with stock converter but better with 2000+ stall. Use lower gears. Mild rough idle.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

SMALL BLOCK CHEVY HYDRAULIC COMPLETE KIT – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Strong torque, good mileage, stock to mildly modified combinations.

The COMP Cams 08-303-8 Nitrous HP Hydraulic Roller Camshaft is a high-performance upgrade for Chevy Small Block engines, designed to maximize horsepower under nitrous or mild boost while maintaining strong street/strip drivability.

“Edelbrock Rollin’ Thunder Camshaft No: 2210 is designed for small-block Chevy engines from 1957-86 and produce optimum torque from the low-end to the mid-range. Rollin’ Thunder camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 440HP and 425 Ft Lbs of Torque when paired with Pro-Flo XT EFI system No: 3528 and RPM E-Tec cylinder heads No: 60975. Must be used with thrust button, high stall torque converter, and stock ratio rocker arms only. Camshaft specifications: – Intake duration: 262 Degrees – Exhaust duration: 266 Degrees – Intake lift: .628″” – Exhaust lift: .608″” – Lobe separation: 114 Degree – Intake Center Line: 109 Degree – Vacuum: 13″””

Mild street performance, slightly noticeable idle. Needs aftermarket intake, headers, 3.40-4.10 gears.

Mild performance for TPI. Strong low to mid-range power. Requires custom tuning.

The COMP Cams 08-501-8 Xtreme Energy Hydraulic Roller Camshaft is designed to deliver aggressive performance gains while maintaining excellent street manners, making it a top choice for small block Chevy enthusiasts.

Competition Cams Reduced Travel OE-Style Hydraulic Roller Lifter for ’87+ SBC, LT/LS and V6, 875-1.

Edelbrock part No: 97385 high performance hydraulic roller lifters for 1987 and later small-block Chevys are the perfect match for Edelbrock Rollin’ Thunder hydraulic roller cams. They are a drop-in replacement for 1987 and later blocks that accept factory roller camshafts. These precision hydraulic roller lifters feature tight ID tolerances that allow for better control at higher RPM and a micro finish OD for reduced friction.

Value-priced seal meets all cataloged application requirements.