from

$13.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$93.99

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading limited warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading limited warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
Regulators and rectifiers are 100% electronically load tested for reliable charging performance
100% new OE-quality brushes and bearings are used to ensure long service life
Rotors and stators are load tested and double insulated for maximum charging performance
Slip rings are precision polished for maximum brush contact and service life
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$94.99

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
Regulators and rectifiers are 100% electronically load tested for reliable charging performance
100% new OE-quality brushes and bearings are used to ensure long service life
Rotors and stators are load tested and double insulated for maximum charging performance
Slip rings are precision polished for maximum brush contact and service life
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$14.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$21.99

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure accurate signal output providing product reliability, every time.

from

$1.99

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$1.99

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$11.49

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

Application matched components ensure the charging system can be returned to like new condition.

from

$6.29

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

Application matched components ensure the charging system can be returned to like new condition.

from

$2.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$4.99

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

Application matched components ensure the charging system can be returned to like new condition.

from

$449.99

Our DynaForce starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The DynaForce starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans. Denso Style starter with “Nose” on the rear of the starter housing for engines with pilot hole applications. The 4.4:1 gear reduction provides high torque for easy starting of stock and high compression engines.

Product Features:

Also Available in Black
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking
Downsized design helps clearance issues
Mount can be clocked to assist in mounting

from

$99.99

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by a Limited Warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:

Each unit is triple-tested to ensure quality and performance
All wear components (brushes, bushings, and bearings) are replaced with all NEW components in the remanufacturing process
Tech Hotline with trained ASE Certified Technicians: Call Carquest Technical Support at 1-800-228-9672
Remanufactured by an IATF/TS 16949 certified supplier, ensuring adherence to the highest industry standards for quality and reliability.
Designed to meet or exceed OE specifications for fit, form, and function, providing seamless compatibility and dependable performance.

from

$31.99

This ignition lock cylinder is designed to match the fit, function and performance of the original equipment part on specified vehicles. It is engineered to help restore ignition lock function when an original cylinder is broken or worn out.

Product Features:

Direct replacement – this ignition lock cylinder matches the fit and function of the original equipment assembly on certain vehicle years, makes and models
Ideal solution – engineered to help restore and ensure the functionality of the lock cylinder
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$12.99

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure confidence and product reliability, every time.

from

$17.99

The Ignition switch is the main power switched distribution point in every vehicle. The ignition switch in some manner will be connected directly to the vehicle battery and then supply power out to every operating system in the vehicle that is required to be connected and disconnected from the vehicle’s battery or power source.

Product Features:

Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure confidence and product reliability, every time.

from

$71.99

ACDelco Professional Voltage Regulator is a high quality aftermarket replacement component for one or more of the following vehicle systems: starting and charging. This premium aftermarket motor is manufactured to meet or exceed your expectations for fit, form, and function.

Product Features:

Professional, premium aftermarket replacement
Provides the performance and dependability you expect from ACDelco
Manufactured to meet expectations for fit, form, and function

from

$78.99

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

from

$38.99

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications.

Product Features:

CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

from

$19.49

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$90.99

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features: