Dodge W100 Carburetor Parts

Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.

Product Features:

• Rubber Material
• For Holley®, Barry Grant, And Demon Gasoline Carburetors
• No Hardware Included
• 50cc Volume
• Made iIn The USA

The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline No: 12400 for 4150 Carburetors Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

Product Features:

• The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline No: 12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
• Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45

Product Features:

• Fits Holley® Carburetors With Center Hung Fuel Bowl
• Includes Adjusting Nut
• Includes Locking Screw
• Includes O-Ring
• Includes Washers

Edelbrock Transfer Tube O-Rings Pair No. 12416 Will Fit Holley 4150, 4160, 4165 &4175 Series Carb

The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var

Product Features:

• Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
• Includes Gasket
• 1/2 in. x 28 Power Valve Thread
• For Applications That Prefer To Run Carbs Without The Power Valves
• Made In The USA

The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:

• Gasket Or Seal Included
• 3.5 in. Hg Opening Vacuum
• Single Stage
• Standard Flow Type
• Made In The USA

The Edelbrock No. 12685 Single Stage 8.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

• Center Hung Floats
• 0.11 in. Needle Diameter
• Viton® Needle Material
• Sold Individually
• Non-Adjustable Type

The Edelbrock No. 12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 carburetors. Kit includes two black nitrile fuel bowl gaskets.

Product Features:

• The Edelbrock No: 12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
• Kit includes two black nitrile fuel bowl gaskets.

The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.

Product Features:

• Nitrile Rubber Material
• Metering Block Type
• Set of 4
• Fits Holley® 4160 Carburetors
• Made In The USA

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.

Product Features:

• Nitrile Rubber Material
• Metering Block, Fuel Bowl Type
• Set of 4
• Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
• Made In The USA

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

The Ultra Street Avenger carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Street Avenger carburetors have the same great features as their aluminum counterparts such as a tumble polished aluminum finish; quick change vacuum secondaries for easy tuning to optimize performance or fuel economy; four vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included fuel line kit so there are no unnecessary trips back to the parts store. Ultra Street Avengers feature the same optimized street calibration as the zinc versions so you know they will run great on your vehicle. In addition, the Ultra Street Avenger now comes with anodized metering blocks and a base plate made from 6061-T6 billet aluminum and a built in, clear fuel level sight glass for easy, no mess fuel level adjustments. Don’t trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

• Ultra Street Avenger Has Optimized Calibration Works Out Of Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• Built In Clear Fuel Level Sight Glass For Fuel Level Adjustment
• Aluminum Construction For A 43% Weight Savings
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

Holley Double Pumper(R) carburetors are a perfect performance upgrade for hot street cars and race vehicles. Double Pumper carburetors are an American icon when it comes to performance carburetors. From their roots as the premier carburetor on many factory muscle cars to powering thousands of vehicles across the finish line, the Double Pumper is a great choice whether you are burning up the street or the quarter mile.

Product Features:

• Metering Blocks Base Plate For Good Looks True Gasket Sealing
• Optimized Street/Strip Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Mechanical Secondaries For Awesome Tire Turning Performance
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• Clear Fuel Level Sight Glass No Mess Fuel Level Adjustments
• Aluminum Construction For A 43% Weight Savings
• Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The Edelbrock 94 No. 12466 Carburetor Jets .066″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12463 Carburetor Jets .063″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12462 Carburetor Jets .062″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12479 Carburetor Jets .079″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12467 Carburetor Jets .067″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12468 Carburetor Jets .068″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12478 Carburetor Jets .078″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.