Dodge St. Regis Performance and Racing Products

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

Product Features:

• Rolled Edges For Strength
• Ideal For Magnetos
• Ideal For Ignition Distributor

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

• Designed to allow high flow rates and a consistent flow of oil to your engine
• Pleated synthetic-blend filtration media removes most harmful contaminants
• Fast and easy Wrench-Off removal using the welded one-inch hex nut
• High capacity to withstand the service intervals recommended by vehicle manufacturers
• Heavy-duty canister for outstanding durability
• Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
• Designed to operate with all synthetic, conventional, and blended motor oils
• 1-Year Limited Warranty

Graphite & steel construction, proprietary polymer coated. 4.140 inch Gasket Bore, .028 inch Compressed Thickness.

Product Features:

• Steel Shimmed For Perfect Sealing
• Increases Engine Compression
• High Temp Silicone Coated To Prevent Leaks
• Stress Formed Embossments

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Chrome plated stamped steel valve covers have a flat smooth top, with internal baffles. Tall-style cover provides extra valve train clearance. Sold as a pair. Will not fit Magnum style heads.

Product Features:

• Fits Chrysler small block (pre-Magnum style heads)
• Chrome plated steel
• Tall-style covers provide extra clearance
• Sold as a pair
• Cadmium Plated To Resist Corrosion
• Easy Installation

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Product Features:

• Best with aftermarket torque converters and 9.5:1 compression.
• Great high RPM power.
• Easy on valve train parts.
• Can be used with mild ratio rocker arms and traditional performance valve springs.

For 3500 to 8000 RPM high-performance engines. For standard rectangular port heads. For oval track and drag race engines. Superior horse power and torque potential.

Product Features:

• For 3500 to 8000 RPM High-Performance Engines
• For Standard Rectangular Port Heads
• For Oval Track/Drag Race Engines
• Superior Horse Power And Torque Potential

When installing headers you will need header bolts, factory exhaust manifold bolts won’t work. These Mr. Gasket Header Bolts are Grade 5 for strength, black oxide coated, and have a compact hex head that is ideal for use where space is minimal – your typical header flanges. Sold as a set of 14.

Product Features:

• 14 per Package
• Heat-Treated For Strength
• Ideal For Tight Spaces
• Grade 5 Material
• Protective Black Finish

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 3/8″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

Product Features:

• 5/16 in. Thick
• Conforms to warped flanges, giving them better sealing capabilities
• Graphite-impregnated facing and steel expanded metal core
• Does not deteriorate or crack under excessive heat and pressure
• Sold as a pair

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

• Gold Dichromate Finish For Extreme Off Road Environments
• Single Feed Fuel Inlet For Ease Of Installation
• Optimized Off-Road Calibration That Works Out-Of-The-Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• One Piece Off-Road Vent Tube Eliminates Fuel Spillover
• Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
• Limited Lifetime Warranty Defects In Material/Workmanship

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

RngPnn

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

• Improved output coil for electronic ignitions
• Works w/Blaster Ignition Or MSD 5/6/7 Series
• Ballast Resistor Required If Used w/Stock Points Ignition
• Alkyd tower w/high dielectric properties lessens carbon tracking

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Knowing your coolant temperature can help to prevent burn injuries. Thermocap Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermocap Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree F temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges.

Product Features:

• Indicates Coolant Temperature
• Helps to Prevent Injuries from coolant or steam burns
• Integrated Coolant Reclamation Valve
• Improves Underhood Appearance
• Fahrenheit and centigrade readings
• Various valve pressures available

The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

Product Features:

• Forward and Reverse Shift Patterns
• Chrome Plated Trigger for Detent Activity
• Factory Neutral Safety Switch
• Compact And Lightweight
• Roller Detent with Shifter Pattern

Features include NHRA/ IHRA reverse lockout, backup light switch, neutral safety switch, polished T-handle. Cable operated for quick installation and accurate shifting. For 2 and 3 speed applications.

Product Features:

• Base Trims For Custom Fit
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Includes Neutral Safety Switch
• Polished Aluminum. T-Handle and Cable

The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

Product Features:

• Forward and Reverse Shift Patterns
• Chrome Plated Trigger for Detent Activity
• Factory Neutral Safety Switch
• Compact And Lightweight
• Roller Detent with Shifter Pattern

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

• Universal Floor Mount Application
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Use w/Reverse Pattern Valve Body
• Includes Neutral Safety Switch
• Includes Backup Light Switch

The B&M Sport Shifter features, Neutral safety switch, backup light switch, lighted gear indicator and black T-Handle and cable. Fits Most 3 and 4 Speed applications.

Product Features:

• Base Trims For Custom Fit
• Neutral Safety Switch
• Backup Light Switch
• Lighted Gear Indicator
• Black T-Handle and Cable