Dodge RD200 Air Intakes
Top Dodge RD200 Air Intakes Categories
We carry over 134 Air Intakes in inventory for the Dodge RD200. If you’re looking for aftermarket Air Intakes for your Dodge RD200, check out all these categories:
Essential Dodge RD200 Air Intakes
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Holley – Carburetor – 750 CFM Street Hp Mech Sec (Part No.0-82751)
from
$799.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Calibration For Outstanding Drivability
- Contoured Venturi Inlet Balances Airflow For Increased hp
- Screw In Air Bleeds For Precision Tuning Capabilities
- Four Corner Idle For Precise Idle Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Intended For Lightweight Vehicles w/Man/Auto Trans
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Throttle Lever #1481 For Chrysler 1966 And Later, Gold Iridited Finish (Part No.1481)
from
$18.99Product Features:
- Converts Throttle Lever on Carb for Proper Use
- For Edelbrock Performer Series Carburetors Only
- Also Accepts Cruise Control
Edelbrock – Intake Manifold Gasket for 1966-87 318-340-360 Chrysler engines (Part No.7276)
from
$30.99
Product Features:
See More
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Carquest – Carburetor Choke Pull-Off (Part No.779-6066)
from
$24.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$17.99
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$36.99
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Edelbrock – Performer RPM Small Block Chrysler Intake Manifold (Part No.7176)
from
$464.99Product Features:
- Best for the Ultimate in Street High-Performance
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
- Edelbrock Total Power Package Maximizes Gains
- Cast Finish
Edelbrock – Performer Intake Manifold Small-Block Chrysler (Part No.3776)
from
$472.99
Product Features:
See More
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1874)
from
$32.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1753)
from
$35.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Felpro – Carburetor Mounting Gasket (Part No.60188)
from
$8.79
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Dodge RD200 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Dodge RD200
You love your RD200. So we’ve made it easier than ever to help you find Dodge RD200 Air Intakes in our online catalog. Our inventory holds 134 aftermarket and OEM Air Intakes for your Dodge RD200, ranging from $4.29 to $1,949.99.
We offer parts from 8 brands trusted to make quality Air Intakes for your Dodge RD200. Before you buy, take some time to read through customer reviews. We currently have 431 reviews of Dodge RD200 Air Intakes from previous customers. Some of the top rated parts include Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Street Carbs with 3.4 stars.
Find your RD200 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Dodge RD200 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Dodge RD200
Our inventory holds Air Intakes for your Dodge RD200 from 8 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, FELPRO, and Mr. Gasket, all of which can keep that Dodge happy.
We have Felpro parts available for your Dodge RD200 in categories like Intake Manifold Parts and Carburetor Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Dodge RD200 across several catalog categories, including Carburetor Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Carburetors
FAQs for Dodge RD200 Air Intakes
What are the most purchased Air Intakes for the Dodge RD200?
Out of 134 Air Intakes for the Dodge RD200, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
What are the top-rated Dodge RD200 Air Intakes?
Top-rated Air Intakes for your Dodge RD200 based on customer reviews/ratings are:
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
