Dodge Ramcharger Performance and Racing Products

Designed to fit Hooker Competition header, Manifold or catalytic converter back applications. Cat-back kits install behind the converter and all other applicable emission control devices.

Product Features:

• Reducer Flex-Tubes
• Reduces Backpressure
• Hardware Included
• Instructions Included

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

• Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Uf-198
• MSD 8228
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

• Maintains Better Alignment While Driving
• Full Floating and Non Binding
• Fits Into the Remaining Stock Control Arms

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

• Made of Superior Hyper-Flex+ Material
• Adds Dramatic Amount of Performance/Durability
• Helps Vehicle Be in Control
• Allows the Suspension to Function Properly

Product Features:

• Non-Rotator Type
• 1.550 in. Outer Diameter
• .190 Wire Size
• Single Coil Spring Type
• Set of 16

A true performance application component for cars, trucks, hot rod, for racing and competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

• Made from HYPER-Flex Polyurethane
• Firm Enough for Huge Amounts of Horsepower/Torque
• Soft Enough Not to Transmit Vibration

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

Product Features:

• Rolled Edges For Strength
• Ideal For Magnetos
• Ideal For Ignition Distributor

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

• Easy to Install
• Superior Material
• Saves Your Tie Rods
• Lasts Longer
• Looks Great

Product Features:

• CHRYS 9 1/4″ OPEN EMPTY CASE CAN USE ABS RING.

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

• Allows Sway Bar System to Work At 100% Efficiency
• Zerk Type Fittings
• Allows for Periodic Greasing
• Lasts Much Longer Than OEM Rubber Bushings
• Handling Characteristics Improve Dramatically

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

• Universal Floor Mount Application
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Use w/Reverse Pattern Valve Body
• Includes Neutral Safety Switch
• Includes Backup Light Switch

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

• Designed to allow high flow rates and a consistent flow of oil to your engine
• Pleated synthetic-blend filtration media removes most harmful contaminants
• Fast and easy Wrench-Off removal using the welded one-inch hex nut
• High capacity to withstand the service intervals recommended by vehicle manufacturers
• Heavy-duty canister for outstanding durability
• Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
• Designed to operate with all synthetic, conventional, and blended motor oils
• 1-Year Limited Warranty

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Mr. Gasket Performance Series intake gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Performance Material – Cellulose/Nitrile Composition
• .060″ Thick
• Can Be Trimmed To Meet Your Specifications

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:

• Made from HYPER-Flex Polyurethane

When installing headers you will need header bolts, factory exhaust manifold bolts won’t work. These Mr. Gasket Header Bolts are Grade 5 for strength, black oxide coated, and have a compact hex head that is ideal for use where space is minimal – your typical header flanges. Sold as a set of 14.

Product Features:

• 14 per Package
• Heat-Treated For Strength
• Ideal For Tight Spaces
• Grade 5 Material
• Protective Black Finish

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 7 1¿4″ diameter
• 7 1┐4″ diameter
• 383 thru 440 cu. in.
• Increased Performance
• Set Valve Lash At Proper Time

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

• Maintains Better Alignment While Driving
• Full Floating and Non Binding
• Fits Into the Remaining Stock Control Arms

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

• Smaller diameter CNC machined billet aluminum housing
• Billet aluminum base clears aftermarket heads and valve covers
• Must Be Used w/An MSD Ignition Control
• Supplied w/small dia. cap w/HEI style terminals; race and rotor
• Will accept PN[8441] Cap-A-Dapt
• Mechanical advance assembly can be locked out for crank trigger systems
• Advance weight pins are staked and tig welded to the plate
• Nylon pads ensure smooth operation of the advance weights

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Product Features:

• Incredible Improvement in Control
• Maintains Proper Caster and Camber Alignment
• Increase in Handling and Control
• Greatly Reduce Wheel Hop on Quick Acceleration
• Even Braking Control is Improved
• Better Suspension Stability