from

$74.99

11.5″ GM & Chrysler crush sleeve. Approx 0.935″ long.

Product Features:

Crush sleeve for GM and Chrysler 11.5″
0.935″ tall

from

$57.99

9.25″ cross pin shaft TracLoc ONLY, not standard Open 0.870″ DIA.

Product Features:

Cross pin shaft for Chrysler 9.25″
Fits Trac Loc positraction only
0.870″ diameter

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$39.99

Product Features:

MINI INSTALL KIT CHRYSLER 8.25 8 1/4″

from

$269.99

Dana 60 & Dana 61 TracLoc clutch set.

Product Features:

Clutch kit
Fit Dana Spicer 60 Trac Loc positraction

from

$6.99

Product Features:

Outer slinger
Fits Dana Spicer 80

from

$11.29

Product Features:

O-ring for seal housing
Fits Dana Spicer 60

from

$9.29

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$7.99

11.5″ & 10.5″ Chrysler ring gear bolt.

Product Features:

Ring gear bolt for GM and Chrysler 11.5″ and Chrysler 10.5″

from

$186.99

Product Features:

FULL SPOOL DANA 60 35 SPLINE 4.10 & DOWN

from

$394.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, 80 with a length of 36.5 inches and 35 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
36.5″ long
Fits Dana Spicer 60, 70 and 80

from

$7.99

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

Power Lok case bolt for Dana Spicer 60 and 70
7/16 x 14 thread
3.5″ long
9/16″ hex head

from

$1145.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

Fits Dana Spicer 60 with 40 spline axles
4.10 and down ratio only
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$254.99

Product Features:

CHRY 12BLT 9.25 R&P-4.56 RATIO

from

$13.99

Model 35 (standard Open & TracLoc) 8.25″ Chrysler TracLoc cross pin bolt.

Product Features:

Cross pin bolt for AMC Model 35 with c-clip axles

from

$159.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$78.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for ’76 & up Chrysler 8.25″ rear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Includes carrier bearings and races

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$1049.99

Yukon Trac Lok positraction internals for Dana 80 and with 35 spline axles. Uses round design cross pin. (Not for Dana 60 or 70). Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects. Dana 80 Trac Lok spider gears, 35spline (” round” design cross pin, NOT Dana 60 or NOT Dana 70 ).

Product Features:

Spider gear kit
Fit Dana Spicer 80 Powr Lok positraction with 35 spline axles
Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

from

$1168.99

Differential

from

$235.99

Yukon replacement yoke for Dana 80 with a 1480 U/joint size. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 80
37 spline
1480 u-joint size
4.188″ snap ring span
1.375″ cap diameter
Outside snap ring design
Strap style

from

$22.79

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$1806.99

11.5″ Chrysler Helical gear Type positraction.

Product Features:

Fits GM and Chrysler 11.5″
30 spline

from

$234.99

A worn or damaged differential pinion flange can lead to driveline Vibrations! And fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience