Dodge Ram 1500 Pickup Differentials

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• 4.10 and down ratio only
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Powr Lok positraction only

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Yukon standard open spider gear kit for 8″ Chrysler with 29 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Chrysler 8.0″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

9.25″ pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer for Chrysler 9.25″ rear

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 60
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

A worn or damaged differential pinion flange can lead to driveline Vibrations! And fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

• Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
• Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

USA Standard axle for ’94 & up Chrysler 9.25″ truck rear. This axle measures 34 1/16″ and has 31 spines. This is a non-ABS axle.

Product Features:

• Fits 1994 and up Chrysler 9.25″ truck rear for 2 wheel drive and 4 wheel drive
• 31 spline
• 34 1/16″ long
• 5 lug
• This axle is not compatible with ABS applications

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Dana Spicer 60 front
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil baffles and slingers, thread locker, marking compound with brush and gasket.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits late 2003 and up Chrysler 8.0″ IFS
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Dana Spicer 60 rear
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and gasket.

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only

Product Features:

• Pinion nut
• Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Yukon round replacement yoke companion flange for Dana 60 and 70. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60 and 70
• 29 spline
• 5.00″ O.D.
• 8 x 4.25″ bolt pattern
• Round companion flange

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Product Features:

• KIT SHIM PINION

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool