Dodge Ram 1500 Performance Ignition Products

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Uf-198
• MSD 8228
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Fire up your late model hemi with a set of MSD’s blaster coils. The coils are a direct bolt-in and are spec’d with superior materials and winding ratios to improve the output of the coil while retaining the factory fit.

Product Features:

• Improved High RPM Operation
• Patented Winding Design and Materials
• Direct Bolt-In to Factory Connectors
• Secondary Current (mA): 56 mA

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

In some instances when you install an MSD ignition, the factory ECU may not be able to distinguish when the coil fires. This is the signal that is also responsible for firing the injectors (or the tachometer), which may cause a no-run situation. The dual channel ignition adapter simulates the original coil trigger signal thus allowing the ECU to properly trigger both the tach and fuel injection with the MSD DIS ignition installed. In most cases, the adapter plugs directly into the MSD’s harness. For vehicles using an MSD DIS-2 ignition, only one PN 8912 is required. For DIS-4 applications, two PN 8912’s are required.

Product Features:

• Designed for non-current limiting ignitions
• Size Non-Current Limiting Ignitions
• Easy mounting and installation
• Simulates the coil signal

These MSD 6-Hemi ignition controllers fire the coils and control the timing on Hemis that are retro-fit with a carburetor or late model factory electronic fuel injection. You program two separate rev limits and have a single-step retard adjustment. The MSD 6-Hemi ignition controllers connect easily, directly to the coils, crankshaft, cam, and MAP sensors for a simple installation. Wiring harnesses for installing on factory EFI engines are sold separately.

Product Features:

• Fires Coils and Controls Timing on Hemis Retro-Tit
• Program two rev limits and a step retard
• Can be used w/Carburetor or factory EFI
• Easily connects directly to coils/crank/cam/MAP sensors

Allows you to directly plug into the ACCEL PN 140021 Super coil when being used on a 1998 to 2002 Dodge truck, or Jeep equipped with a distributor and the newer light grey Yazaki wire harness coil connector. No cutting or splicing is required.

Product Features:

• Nice Clean Connection
• Easy Installation

Product Features:

• Service Part
• Makes Connections Quick And Easy

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils