Dodge D300 Pickup Air Intakes
Top Dodge D300 Pickup Air Intakes Categories
We carry over 166 Air Intakes in inventory for the Dodge D300 Pickup. If you’re looking for aftermarket Air Intakes for your Dodge D300 Pickup, check out all these categories:
Essential Dodge D300 Pickup Air Intakes
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1874)
from
$32.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Throttle Lever #1481 For Chrysler 1966 And Later, Gold Iridited Finish (Part No.1481)
from
$18.99Product Features:
- Converts Throttle Lever on Carb for Proper Use
- For Edelbrock Performer Series Carburetors Only
- Also Accepts Cruise Control
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Performer RPM Small Block Chrysler Intake Manifold (Part No.7176)
from
$464.99Product Features:
- Best for the Ultimate in Street High-Performance
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
- Edelbrock Total Power Package Maximizes Gains
- Cast Finish
Felpro – Carburetor Mounting Gasket (Part No.8632)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$50.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$17.99
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Carquest – Carburetor Choke Pull-Off (Part No.779-6066)
from
$24.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Holley – Street Carburetor: 750 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80459SA)
from
$536.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Factory Preset Electric Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow-Out Protection
- 100% Wet Flow Tested By Holley Technicians
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Felpro – Air Cleaner Mounting Gasket (Part No.11528)
from
$2.49
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Felpro – Valley Pan Gasket Set (Part No.MS 96000)
from
$37.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
Mr. Gasket – Intake Gasket (Part No.301)
from
$41.99
Mr. Gasket Performance Series intake gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Performance Material – Cellulose/Nitrile Composition
- .060″ Thick
- Can Be Trimmed To Meet Your Specifications
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12458 Size .057 (Pair) (Part No.12458)
from
$14.99
The Edelbrock 94 #12458 Carburetor Jets .058″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 58 Maximum Jet Size
- 0.057 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Dodge D300 Pickup Air Intakes Categories
Helping You Find the Right Air Intakes for Your Dodge D300 Pickup
You love your D300 Pickup. So we’ve made it easier than ever to help you find Dodge D300 Pickup Air Intakes in our online catalog. Our inventory holds 166 aftermarket and OEM Air Intakes for your Dodge D300 Pickup, ranging from $2.49 to $1,949.99.
We offer parts from 9 brands trusted to make quality Air Intakes for your Dodge D300 Pickup. Before you buy, take some time to read through customer reviews. We currently have 3,399 reviews of Dodge D300 Pickup Air Intakes from previous customers. Some of the top rated parts include Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.7 stars and Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.9 stars.
Find your D300 Pickup Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Dodge D300 Pickup part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Dodge D300 Pickup
Our inventory holds Air Intakes for your Dodge D300 Pickup from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, FELPRO, and Dorman, all of which can keep that Dodge happy.
We have Felpro parts available for your Dodge D300 Pickup in categories like Intake Manifold Parts. Some of the top-rated Felpro parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Dodge D300 Pickup across several catalog categories, including Carburetor Parts and Air Cleaner Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$46.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
FAQs for Dodge D300 Pickup Air Intakes
What are the most purchased Air Intakes for the Dodge D300 Pickup?
Out of 166 Air Intakes for the Dodge D300 Pickup, the most popular in our inventory are:
from
$2.99
This product is not rated
Steel Cup Expansion Plug 1-1/4 In., SC, Height 0.300
Intake Manifold Expansion Plugs
What are the top-rated Dodge D300 Pickup Air Intakes?
Top-rated Air Intakes for your Dodge D300 Pickup based on customer reviews/ratings are:
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
from
$50.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
“Black is the key word on this 1979 Corvette. I’ve found every performance part imaginable ready to go in black I’m going with a Demon carburetor with”
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
