Dodge D200 Differentials

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 60 rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Yukon replacement positraction internals for Dana 60 (full- and semi-floating) with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Dana Spicer 60 with Trac Loc positraction with 35 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Yukon replacement yoke for Dana 60 and 70 with fine spline axles and a 7290 U/joint size. 2.625″ snap ring span. 1.125″ cap diameter. Inside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60, 70, 70U and 70HD
• 29 spline
• 7290 u-joint size
• 2.625″ snap ring span
• 1.125″ cap diameter
• Inside snap ring design
• Strap style

CONE

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Product Features:

• 31 spline
• 5 x 4.5″ bolt pattern
• 31 11/16″ long
• Fits Chrysler 9.25″ in 1979 and down Dodge truck

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

• Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

• Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
• 1/2″ x 18 thread

8.25″ Chrysler pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Chrysler 8.25″

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88510 race
• All steel construction

Differential

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Low swell in hydrocarbon fluids
• Design type: spring loaded; multi-lip
• Provides good low temperature capability
• Temperature range: -40°F to 225°F; -40°C to 107°C
• Delivers quality and reliable performance for every type of repair

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Product Features:

• KIT SHIM PINION

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 30 spline axles
• 4.56 and up ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

Product Features:

• Carrier shims for Dana Spicer 60 and 70U

Dana 60 & Dana 61 TracLoc clutch set.

Product Features:

• Clutch kit
• Fit Dana Spicer 60 Trac Loc positraction

Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.

Product Features:

• Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
• 7/8″ x 14 thread
• 1 5/16″ socket

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

• Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles.
• Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged.
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Chrysler 9.25″ rear
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.