Dodge B150 Air Intakes
Top Dodge B150 Air Intakes Categories
We carry over 148 Air Intakes in inventory for the Dodge B150. If you’re looking for aftermarket Air Intakes for your Dodge B150, check out all these categories:
Essential Dodge B150 Air Intakes
Edelbrock – Intake Manifold Gasket for 1966-87 318-340-360 Chrysler engines (Part No.7276)
from
$30.99
Product Features:
See More
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Holley – Carburetor – 770 CFM Alum Street Avenger E/C (Part No.0-83770)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Features A Tumble Polished Finish Can Also Be Hand Polished
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Glass Fuel Level Sight Windows For Easy Safe Float Adjustments
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
Edelbrock – Throttle Lever #1843 For Chrysler 1966 And Later, Black Powder Coated Finish (Part No.1843)
from
$20.99
Converts throttle lever on carburetor for proper use. For Edelbrock performer series carburetors only. Also accepts cruise control. Use appropriate throttle cable plate.
Product Features:
See More
Product Features:
- Converts Throttle Lever on Carb for Proper Use
- For Edelbrock Performer Series Carburetors Only
- Also Accepts Cruise Control
- Use with Appropriate Throttle Cable Plate
Edelbrock – Performer Intake Manifold Small-Block Chrysler (Part No.3776)
from
$472.99
Product Features:
See More
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Carquest – Carburetor Choke Pull-Off (Part No.779-6066)
from
$24.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Carquest Premium – Throttle Position Sensor (Part No.ECC1201)
from
$43.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1874)
from
$32.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Carquest Premium – Air Charge Temperature Sensor (Part No.WTA1087)
from
$27.99
The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.
Product Features:
See More
Product Features:
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
- 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
- 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
- Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
- Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
- Application matched components ensures system operation in like new condition.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$17.99
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Carquest Premium – Multi-Use Connector (Part No.PTA1166)
from
$20.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Dodge B150 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Dodge B150
You love your B150. So we’ve made it easier than ever to help you find Dodge B150 Air Intakes in our online catalog. Our inventory holds 148 aftermarket and OEM Air Intakes for your Dodge B150, ranging from $2.99 to $1,949.99.
We offer parts from 11 brands trusted to make quality Air Intakes for your Dodge B150. Before you buy, take some time to read through customer reviews. We currently have 2,558 reviews of Dodge B150 Air Intakes from previous customers. Some of the top rated parts include Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.7 stars and Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.9 stars.
Find your B150 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Dodge B150 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Dodge B150
Our inventory holds Air Intakes for your Dodge B150 from 11 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, FELPRO, and Dorman, all of which can keep that Dodge happy.
We have United Carb parts available for your Dodge B150 in categories like Carburetor Parts. Some of the top-rated United Carb parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Dodge B150 across several catalog categories, including Carburetor Parts and Air Cleaner Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$46.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
FAQs for Dodge B150 Air Intakes
What are the most purchased Air Intakes for the Dodge B150?
Out of 148 Air Intakes for the Dodge B150, the most popular in our inventory are:
from
$2.99
This product is not rated
Steel Cup Expansion Plug 1-1/4 In., SC, Height 0.300
Intake Manifold Expansion Plugs
What are the top-rated Dodge B150 Air Intakes?
Top-rated Air Intakes for your Dodge B150 based on customer reviews/ratings are:
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
from
$50.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
“Black is the key word on this 1979 Corvette. I’ve found every performance part imaginable ready to go in black I’m going with a Demon carburetor with”
from
$39.99
(8)
Lower & Upper Intake Manifold Gasket Set: 37 Piece Set
“this kit is well designed. contains the gaskets needed to install the intake manifold and the new manifold screws are a added bonus. many of my old ma”
