Chevrolet Yeoman Performance Engines

Edelbrock No: 7251 Engine Water Pump Gasket Set Chevy Small Block. Is it time to rebuild your Edelbrock mechanical water pump- No problem- these Edelbrock water pump gaskets will keep your water pump leak-free. They are manufactured from quality materials and can be installed easily without any modifications

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Dual-plane high-rise intake. For square bore carburetors only. For street and high performance use. Available in cast, polished or endurashine finish.

Edelbrock Pro-Flo XT Small Block Chevy EFI Black Intake Manifold, 71373.

“With a .625″” maximum lift, these Beehive Valve Springs were designed for hydraulic roller cams in LS1, LS2 and LS6 engines. COMP Cams Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life. Because of the unique Beehive design, the valve train can handle more RPM and more aggressive cam profiles.”

The Edelbrock No: 5792 Sure Seat Valve Spring for Chrysler 383-400-413-440 V8 1969-79 O.E Cast iron cylinder heads are made of highest quality spring wire and precision wound to close tolerances, our Sure Seat Valve Spring sets are for use on original equipment heads when installing Edelbrock Performer-Plus, Performer RPM and Torker-Plus camshafts. These are the same high-performance springs used on Edelbrock Performer and RPM cylinder heads. For camshaft warranty compliance, use only the springs recommended by Edelbrock for each camshaft application.

“Competition Cams Ultra Pro Magnum Rocker Arm Set with 1.6 Ratio for Chevrolet SBC with 7/16″” Stud, 1605-16. ”

This is a high quality gasket that will seal that leaking water neck, and provide you with years of service. This gasket works well in all applications.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Edelbrock Small-Block Chevy E-Street Cylinder Heads 64cc, 5089.

Edelbrock Small-Block Chevy E-Street Cylinder Head 70cc Pair, 5073.

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.

“Edelbrock Performer-Plus Camshaft No: 2102 is designed for 265-400 Chevy V8 engines from 1957-86 and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2102 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 320HP and 382 Ft Lbs of Torque when paired with Performer EPS intake manifold No: 2701 and Performer cylinder heads No: 60909. 50-State Legal E.O. No: D-215-19 for 1957-86 small-block Chevrolet. Camshaft specifications: – Intake duration: 204 Degrees – Exhaust duration: 214 Degrees – Intake lift: .420″” – Exhaust lift: .442″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 14″””

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

SMALL BLOCK CHEVY HYDRAULIC COMPLETE KIT – Thumpr : High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

SMALL BLOCK CHEVY HYDRAULIC COMPLETE KIT – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.