from

$6.29

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$47.99

The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.

Product Features:

Application matched components ensure carburetor can be returned to like new condition.

from

$671.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Manual Choke For Precise Cold Start Control
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians

from

$20.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$60.99

Product Features:

The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
The kit comes with the necessary components to rebuild a 4150 style Carburetor.

from

$10.49

This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$14.99

The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45

Product Features:

Fits Holley® Carburetors With Center Hung Fuel Bowl
Includes Adjusting Nut
Includes Locking Screw
Includes O-Ring
Includes Washers

from

$16.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$14.99

The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

Product Features:

57 Maximum Jet Size
0.056 in. Orifice Diameter
1/14-32 in. Thread Size
Standard Main Jet Type
Set of 2

from

$20.99

The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.

Product Features:

Nitrile Rubber Material
Metering Block Type
Set of 4
Fits Holley® 4160 Carburetors
Made In The USA

from

$13.99

Product Features:

The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

from

$60.99

Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.

Product Features:

Nominally Rated At 170,000 PSI Tensile Strength
Precision Machined Threads For Secure Engagement, And Would not Rust
Wide Under Head Flange And Companion Washers Provide Even Load Distribution
Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
Facilitates Optimum Sealing Of Gasket Surfaces

from

$22.99

Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to

Product Features:

Brass Material
3/8 in. Single Barb
7/8-20 in. Male End
5/8-18 in. Female Flare
With 3/8 in. Tube

from

$530.99

Edelbrock part #21613 Performer 2-O intake manifold is designed for street 396-502 c.i.d. big-block Chevy V8’s using general duty oval-port cylinder heads. Will not fit under hood of Corvette without hood modifications. Will not fit “tall block” V8’s. May

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
4.3 in. Front Height, 4.85 in. Center Height, 5.4 in. Rear Height
Black Powder Coated Finish
Non-EGR

from

$63.99

Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
Designed to meet or exceed all OEM specifications in fit, form & function
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$4.29

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$4.49

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$66.99

Product Features:

Customize Carburetor Calibration and Performance
Owners Manual has Assembly Help
Includes Metering Rod Retaining Spring
Includes Metering Rods
Includes Metering Jets
Includes Step-Up Springs

from

$17.99

The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:

Gasket Or Seal Included
3.5 in. Hg Opening Vacuum
Single Stage
Standard Flow Type
Made In The USA

from

$22.99

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

Center Hung Floats
0.11 in. Needle Diameter
Viton® Needle Material
Sold Individually
Non-Adjustable Type

from

$5.99

Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.

Product Features:

Manufactured from high quality materials for a long service life
Torque values listed on parts (where applicable)
Easy to install
Constructed to strict engineering quality standards

from

$143.99

Silver Bullet throttle body spacers create turbulence in the air flow at the point just prior entry into the engine increasing horsepower, torque and improving throttle response and fuel efficiency. Silver Bullet throttle body spacers are constructed out of durable T-6061 billet aluminum and using a unique serrated/helix entry to create turbulence at the manifold while eliminating the annoying whistle found in other helix only throttle spacers.

Product Features: