Chevrolet Two-Ten Series Distributors

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Fel-Pro Oil Pan SnapUps 8mm bolts
• Designed to hold up the pan and gasket, for one person installation
• Engine$aver Hardware
• Unsurpassed quality you can trust
• Sold in sets of four and are reusable

Our Chevrolet front drive distributors brought the need for a distributor plug. Both are billet aluminum and feature a slip collar to ensure correct installation depth.

Product Features:

• Use On Engines w/Wet Sump Oil System And Front Drive Dist.
• Supplied w/Bronze Gear
• Must Be Used w/An MSD Crank Trigger
• Adj. slip collar mounting flange for engines w/modified deck hts.
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Oversized Polished Steel Shaft w/QPQ Coating

This is the replacement canister for MSD distributors equipped with vacuum advance (except the PN 8365 and PN 8362 HEI distributors.)

Product Features:

• Replacement Canister
• Vacuum Advance Mechanism
• For Replacement On PN[8460/8461]
• Size Replacement Canister For Distributor PN[8360/8361]

Flame Thrower Street/Strip distributors have a speciallFlame-Thrower Street/Strip distributors have a specially designed HEI distributor module and coil combination which operates without misfire beyond 7500 RPM. That’s nearly 3000 RPM higher than most stock HEI Distributors. Race HEI Distributors feature an electronic HEI Distributor module and 50,000 volt coil combination that optimizes spark energy and peak current to the spark plug in the 6000 to 8500 RPM range.y designed module and coil combination which operates without misfire beyond 7500 RPM

Product Features:

• These vacuum canisters help optimize ignition advance for maximum part throttle performance and cruise speed efficiency.
• Our vacuum lockout plates allow for precise pickup coil position and accurate rotor phasing.

Vacuum Advance & LockoutThese vacuum canisters help optimize ignition advance for maximum part throttle performance and cruise speed efficiency. Our vacuum lockout plates allow for precise pickup coil position and accurate rotor phasing.

Product Features:

• PerTronix D9006 Flame-Thrower HEI Distributor Adjustable Vacuum Advance Canister
• These vacuum canisters help optimize ignition advance for maximum part throttle performance and cruise speed efficiency.

The unique design of these distributors fit tight intake systems while still transferring the high voltage of the MSD racing ignition to the spark plugs. The high voltage carrying capabilities are the result of several features which have been designed to fit the tight quarters and still accurately deliver sparks.

Product Features:

• Designed to fit low in the block to clear firewall/intake combos
• Supplied w/Bronze Gear
• Supplied w/Large Diameter HEI Style Distributor Cap And Rotor
• Must Be Used w/An MSD Crank Trigger And MSD Ignition Control
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Oversized Polished Steel Shaft w/QPQ Coating

Distributors

Marine environments place rigorous demands on every component of the ignition system. The combination of water spray, salt exposure, full throttle acceleration and harsh vibrations all take their toll. The MSD Pro-Billet distributor is the strongest and most accurate distributor you can put in your boat. The housing is CNC-machined from a billet of 6061-T6 aluminum creating a housing with no porosity. Each distributor uses MSD’s race-proven magnetic pickup to trigger the ignition control. Mounted just above the pickup is a mechanical advance assembly that is easy to adjust so you can dial-in an ignition curve to match your boat’s application (except PN 8366). For marine use, the distributor cap is bolted to the aluminum base. There are two flame arrestor holes with brass screens machined into the base of the distributor to prevent ignition of gas fumes that may build up in the engine compartment. A special Weathertight connector is supplied. Underwriter’s laboratory approved.

Product Features:

• For Use In Marine Applications w/Chevy V8 Automotive Engines
• Will not accept a vacuum advance canister
• Supplied w/Bolt Down HEI Style Distributor Cap And Rotor
• Weathertight connectors used for locked and sealed connections
• Must Be Used w/An MSD Ignition Control
• O-ring seals can be installed for oil press. control (Mods only)
• Special oil tract improves lubrication to the dist./cam gear
• Nylon pads ensure smooth operation of the advance weights

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Replacement distributor cap for Flame-Thrower distributors.
• High dielectric strength cap
• Caps for Flame-Thrower “Billet” distributors available with male or female brass terminals.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Replacement distributor cap for Flame-Thrower distributors.
• High dielectric strength cap
• Caps for Flame-Thrower “Billet” distributors available with male or female brass terminals.

Chrome Finish

Product Features:

• Edelbrock part No. 4802 hold-down distributor clamp is for 4.3L V6, small-block V8 and big-block V8 Chevys. It is constructed of die-cast zinc with a chrome finish. Kit includes stud, nut and a washer.
• Includes stud, nut, & washer

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system or operating system fault.

Product Features:

• Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
• Product constructed to meet all design and operating characteristics as intended by the manufacturer.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Product Features:

• All products are constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Cap terminal conductor wires formed with precision guided machines to ensure precise final location in the final housing assembly.
• Terminal inserts manufactured to precise tolerances to ensure a guaranteed electrical connection between the cap conductor wires and spark plug wire terminals.
• Distributor rotor blade coated with RFI coating to prevent electrical magnetic interference with the vehicles electrical system.
• Distributor and rotor housings manufactured using the latest plastic technologies to guarantee di-electric strength and long life cycle.

Edelbrock part No. 22737 is a bronze alloy drive gear for use on ProFlo EFI & Max-Fire distributor in small-block & big-block Chevrolet engines.