Name: Custom Fit Spark Plug Wire Set
Brand: Accel
SKU: 8843
Price: 112.99 USD

from

$112.99

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

8.8mm Graphite Suppression
Silicone Spark Plug Boots
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$42.49

Designed for use with round stick shifters. Complete with chrome ID plate and mounting hardware. Measures: 4-3/8 in. x 5-3/8 in. with 3 pleats.

Product Features:

Complete with Mounting Hardware
Adapt To Most Shifter Install
Hurst Quality
Works Well with Round Shift Levers
Chrome ID Plate

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$334.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$35.99

Product Features:

Valve Cover Gasket

from

$55.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$42.49

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

42000 Volts
Effective To 6500 RPM
Quicker Starting
Improved Throttle Response
Higher RPM Power
Can Finished In Yellow

from

$409.99

These kits include all of the necessary components to rebuild your automatic transmission. OEM style gaskets included. Kits do not include overhaul instructions – please refer to factory shop manual for proper assembly procedures.

Product Features:

Complete High Perf. Or Racing Trans. Overhaul
Includes Only OEM Valvebody Gaskets
Instructions Not Included

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$134.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$798.99

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

For 3500 to 7500 RPM
Use Where Low-End Torque is Not a Prime Factor
Great For Engines w/Slightly Modified Heads
Top Has Vacuum Outlet for Power Brakes
Will Accept Forward and Sideways Mounted Carbs
Carburetor Center-to-Center Dimensions 9.38 in
HEI Ignition Will Not Clear Manifold
Street Machines; Street Rods; Pro-Street; Marine

from

$7.69

CUP

from

$411.99

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

Designed for 2500 to 6500 Performance
Designed for Hi-Perf Street; Drag or Marine Use
Matched to Edelbrock Torker II Intakes
Includes Hydraulic Lifters and Assembly Lube
Dyno Matched/Street Proven Performance
Take The Guesswork Out Of Camshaft Selection

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$32.99

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

Chrome Plated
Grade 5
AN washers with no exposed shoulder for a professional appearance

from

$14.99

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$42.99

This oil filter adapter kit replaces the factory GM (General Motors) oil filter adapter and is manufactured from high grade aluminum. Required for Chevrolet crate engines that does not include an oil filter adapter. Replaces oil filter adapter’s damaged when removing engines to be overhauled. Oil filtered adapter includes filter bypass valve. Uses the following Chevrolet oil filters – AC Delco PF-25 or PF35, Fram PH5 (tall) or PH30, and WIX 51069. Includes mounting bolts.

Product Features:

Replaces GM Oil Filter Adapter #3952301 and 19299222
Fits Chevrolet 307-400 V8 1968-86 and 396-454
Attaches Spin-on Oil Filter To Engines Block
Embossed base provides a leak-free sealing surface. Kit does not come with a gasket
Kit includes Oil Filter adapter and (2) 5/16″-18 x 1.00″ long bolts
Uses the following Filters: Fram PH5(Tall) OR PH30, Wix 51069, AC Delco PF-25 or PF-35.

from

$103.99

Spectre’s Oil Pan was designed for 1965-1990 Big Block Chevrolet 396-454 engines. This stock capacity pan features a raw finish and durable steel construction. Precision engineered for optimum fit and function, this high quality OEM replacement part is easy to install.

Product Features:

For 1965-1990 big block Chevrolet 396-454
Stock capacity
Easy to install with no special tools or skills required
Does not fit GEN V engine with one-piece rear main seal

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$16.99

Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

Product Features:

Chrome Plated Steel
Comes With Gasket

from

$320.99

Product Features:

Easily Concealable
Install In Minutes
Quick Removal
No Obvious Signs Of Installation
No Obvious Signs Of Use

from

$469.99

The Pro-Billet Ready-to-Run distributor is the perfect upgrade for outdated points distributors or bulky HEI. Simply install the distributor in the engine, connect three wires, the coil and fire it up! A maintenance-free magnetic pick-up accurately triggers the module. The increased output of the amplifier easily outperforms stock ignitions and will smooth out the engine’s idle, improve starting and provide a much higher RPM range. The Ready-to-Run features MSD’s adjustable mechanical advance which allows you to custom tailor an ignition curve to match your engine’s needs. There is also a vacuum advance canister to help improve economy. For positive street performance, the Ready-to-Run is the best choice.

Product Features:

Simple and clean three wire installation
Supplied w/An HEI Style Distributor Cap And Rotor
Accepts Cap-A-Dapts
Does not require an MSD Ignition Control
CARB E.O. Approved
Now includes built-in Rev Limiter
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear

from

$29.99

Product Features:

Timing Chain Only

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features: