Chevrolet P30 Van Belts and Hoses

Essential Chevrolet P30 Van Belts and Hoses

Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)

Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415

from

$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to

Product Features:
  • Brass Material
  • 3/8 in. Single Barb
  • 7/8-20 in. Male End
  • 5/8-18 in. Female Flare
  • With 3/8 in. Tube
See More

Driveworks – Automotive V-Belt, Driveworks (Part No.39515)

Automotive V-Belt, Driveworks

from

$5.79
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.

Product Features:
  • This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
  • Polyester cords provide extreme tension-holding capability for longer belt life
  • The raw edge belt design delivers the maximum gripping power
  • The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
See More

Gates – Notched V-Belt: 57.81" Long, 1 Strand, Exact Fit (Part No.7570)

Notched V-Belt: 57.81" Long, 1 Strand, Exact Fit

from

$32.99
Notched V-Belt: 57.81" Long, 1 Strand, Exact Fit

Driveworks – Poly Rib Belt Serpentine Belt; 27.24 Long, 6 Rib Count (Part No.41013)

Poly Rib Belt Serpentine Belt; 27.24 Long, 6 Rib Count

from

$5.49
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.

Product Features:
  • Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
  • No-Noise Advanced Design EPDM rubber compound for quiet extended life
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24" Long, 1.50" Diameter (Part No.E70935)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24" Long, 1.50" Diameter

from

$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot) (Part No.28412)

Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot)

from

$3.99
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Gates – Premium Molded Coolant Hose (Part No.20563)

Premium Molded Coolant Hose

from

$17.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot) (Part No.28411)

Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot)

from

$1.49
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Dayco – Flex Radiator Hoses; EPDM Rubber, 19.88 Inch Long, 1.5 Inch Inner Dia. (Part No.81181)

Flex Radiator Hoses; EPDM Rubber, 19.88 Inch Long, 1.5 Inch Inner Dia.

from

$21.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
  • This hose is designed to prevent splitting, ballooning, and elongation
See More

Gates – Premium Molded Coolant Hose (Part No.20843)

Premium Molded Coolant Hose

from

$21.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia. (Part No.81341)

Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia.

from

$18.79
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
  • This hose is designed to prevent splitting, ballooning, and elongation
See More

Gates – Molded Heater Hose: EPDM, Direct Fit, 1.5" Inside Diameter (Part No.20686)

Molded Heater Hose: EPDM, Direct Fit, 1.5" Inside Diameter

from

$40.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Flex Radiator Hoses; EPDM Rubber, 16.5 Inch Long, 1.75 Inch Inner Dia. (Part No.81331)

Flex Radiator Hoses; EPDM Rubber, 16.5 Inch Long, 1.75 Inch Inner Dia.

from

$21.79
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
  • This hose is designed to prevent splitting, ballooning, and elongation
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Yukon Gear – Seal Puller Tool (Part No.56063)

Seal Puller Tool

from

$57.99
Pinion and axle seal puller. No return.

Product Features:
  • Seal puller
See More

Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25484)

Vulco-Flex« II Flexible Coolant Hose

from

$24.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.

Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Flex Radiator Hoses; Neoprene, HD, 18.75 Inch Long, 1.75 Inch Inner Dia. (Part No.82008GL)

Flex Radiator Hoses; Neoprene, HD, 18.75 Inch Long, 1.75 Inch Inner Dia.

from

$31.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent splitting, ballooning and elongation as well as resist ozone and other detrimental environmental elements, coolants and temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). With corrugations that provide excellent hose flexibility without flattening or collapsing, the Dayco flex radiator hose also features a helical steel coil spring for increased flexibility.

Product Features:
  • Designed to meet OE specifications
  • Not suitable for oil or heat transfer
  • Meets SAE J20R4, Class D-2 requirements for improved service hoses
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 23.25" Long, 1.50" Diameter (Part No.E70724)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 23.25" Long, 1.50" Diameter

from

$43.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

ACDelco – Professional Molded Coolant Hose (Part No.G2000576796ACD)

Professional Molded Coolant Hose

from

$44.48
ACDelco Professional, premium aftermarket Molded Coolant Hoses are composed of specially blended materials to help resist electrochemical degradation (ECD), the leading cause of hose failure. They are specially designed, GM OE style factory-molded hoses to fit today’s smaller, tighter-fitting engine compartments. ACDelco Professional Molded Coolant Hoses are temperature rated from -40 degrees Fahrenheit to 275 degrees Fahrenheit (-40 degrees Celsius to 135 degrees Celsius) and are approved for Marine applications. Do not use for fuel or oil transfer applications. These premium aftermarket replacement molded coolant hoses are manufactured to meet or exceed your expectations for fit, form, and function.

Product Features:
  • Has a heat and ozone resistant cover to increase the life of the hose
  • Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function
  • Made of re-engineered materials to resist vacuum collapse and also reduce the need for internal springs in many applications
  • Installs without buckling, bending out of shape, or straining at the connection for easy installation
  • Inside diameters ranges from 1?4 in to 1 in to fit different types of vehicles
See More

Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25530)

Vulco-Flex½ II Flexible Coolant Hose

from

$33.49
Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Coolant Hose (Part No.20584)

Premium Molded Coolant Hose

from

$33.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25480)

Vulco-Flex« II Flexible Coolant Hose

from

$25.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.

Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18.50" Long, 1.75" Diameter (Part No.E70664)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18.50" Long, 1.75" Diameter

from

$25.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Vulco« Straight Coolant Hose (Part No.24028)

Vulco« Straight Coolant Hose

from

$1.99
Specially engineered stick hose is ideal for straight coolant/air connections in automotive, stationary engine, industrial and home applications.

Product Features:
  • Heat-resistant cover
  • Cover marked in 1 in. increments to facilitate approximate cut lengths, allows ┐custom fit installations
  • Meets SAE 20R1 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: For a maintenance free connection, use PowerGrip SB clamps
  • Caution: Do not use for fuel or oil transfer applications
See More

Helping You Find the Right Belts and Hoses for Your Chevrolet P30 Van

You love your P30 Van. So we’ve made it easier than ever to help you find Chevrolet P30 Van Belts and Hoses in our online catalog. Our inventory holds 142 aftermarket and OEM Belts and Hoses for your Chevrolet P30 Van, ranging from $1.49 to $79.99.

We offer parts from 7 brands trusted to make quality Belts and Hoses for your Chevrolet P30 Van. Before you buy, take some time to read through customer reviews. We currently have 1,999 reviews of Chevrolet P30 Van Belts and Hoses from previous customers. Some of the top rated parts include Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count with 4.3 stars and Automotive V-Belt, Driveworks with 5.0 stars.

Find your P30 Van Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Chevrolet P30 Van part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Belts and Hoses Brands for Your Chevrolet P30 Van

Our inventory holds Belts and Hoses for your Chevrolet P30 Van from 7 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Imperial, and Gates, all of which can keep that Chevrolet happy.
We have Dayco parts available for your Chevrolet P30 Van in categories like Engine Cooling Hoses. Some of the top-rated Dayco parts in these categories are:

Top-Rated Dayco Belts and Hoses

Leading Dayco Belts and Hoses

We carry Dayco brand parts for your Chevrolet P30 Van across several catalog categories, including Radiator Hoses and Serpentine and V Belts. Some of our most reviewed Dayco parts include:

FAQs for Chevrolet P30 Van Belts and Hoses

What are the most purchased Belts and Hoses for the Chevrolet P30 Van?

Out of 142 Belts and Hoses for the Chevrolet P30 Van, the most popular in our inventory are:

What are the top-rated Chevrolet P30 Van Belts and Hoses?

Top-rated Belts and Hoses for your Chevrolet P30 Van based on customer reviews/ratings are:
Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count
from $5.49
(12)
Poly Rib Belt Serpentine Belt; 37.01 Long, 6 Rib Count
“Just a belt”
Automotive V-Belt, Driveworks
from $5.79
(8)
Automotive V-Belt, Driveworks
“Perfect O.E replacement”
Automotive V-Belt
from $5.49
(8)
Automotive V-Belt
“to my car”