Chevrolet Monza Performance and Racing Products

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

Product Features:

• PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
• Precision machined chromoly weights and center plate.

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Spectre’s Chevrolet water neck fits Chevy V8 engines and features a 90 degree neck with a 360 degree swivel design for a custom look and fit. This water neck has been designed around the OEM specifications, has a height of 2-7/8 inches and has a polished aluminum finish for a lasting look that fits great. This water neck includes the allen bolts and sealing O-ring.

Product Features:

• Fits Chevy V8 engines
• 90 degree neck with a 360 degree swivel design
• 2-7/8 inch height
• Includes sealing O-ring and allen bolts
• Polished aluminum finish
• Easy to install

This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:

• Chrome Plated Steel
• Comes With Gasket

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:

• Five layer (graphite core/perforated steel outer layers) composite construction
• Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
• Provides excellent stability, compressibility and high temperature endurance
• Coated with high temperature silicone to ensure sealing of engine fluids
• Will not brinell (indent) aluminum cylinder heads
• For high performance street, drag race and oval track use
• Compatible w/High Octane Fuel
• Compatible With Exotic Fuel

Features include NHRA/ IHRA reverse lockout, backup light switch, neutral safety switch, polished T-handle. Cable operated for quick installation and accurate shifting. For 2 and 3 speed applications.

Product Features:

• Base Trims For Custom Fit
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Includes Neutral Safety Switch
• Polished Aluminum. T-Handle and Cable

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

HYDRAULIC – Magnum: Pro Street/bracket, limited street driving. Intake, gears, 3500+ stall. Racy idle. 10.5:1 compression. OR Drag Race: 3500-4000 stall or 4 speed with 11:1+ compression.

Product Features:

• HYDRAULIC – Magnum: Pro Street/bracket, limited street driving. Intake, gears, 3500+ stall. Racy idle. 10.5:1 compression. OR Drag Race: 3500-4000 stall or 4 speed with 11:1+ compression.
• 305/305 Advertised Duration, 253/253 Duration @ .050″, .525″/.525″ Lift, 110 Lobe Separation
• Valve spring upgrade required

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

• Replacement crank trigger wheel for small block Chevy
• Absolutely the most accurate way to trigger the ignition
• The non-magnetic pickup cannot be false triggered
• Powerful magnets are embedded in a billet aluminum trigger wheel

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

• Built As Matched Assembly
• Exceptional Performance
• Exceptional Durability
• Long Term Dependability
• Designed for Street And Street Strip Applications

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Motive Gear Mini-Spools replace your stock spider and side gears with a solid billet mini-spool for 100% traction to both wheels. Not recommended for street applications.

Product Features:

• Billet construction
• Not recommended for street applications
• GM7.5″ MINI SPOOL 26 SPLINE

High quality valve covers that help you solve rocker clearance issues. Great for when you just can’t seem to stop those thin steel ones from leaking oil. Good for high performance street, drag and oval track racing. They feature an extended sealing lip to positively locate and secure the gasket and stop it from moving to eliminate oil leaks. These Mr. Gasket covers are precision die cast for light weight and a perfect fit.

Product Features:

• Fits small block Chevy engines
• Polished cast aluminum construction
• Tall design cover for added rocker clearance
• Sold as a pair
• Stops Gasket From Moving
• A Perfect Fit
• Beautifully Polished To A High Luster

B&M Transkits give you the same high-quality components that are used in all B&M Street and Strip transmissions. They also include special directions on how to modify your case, pump, and components.

Product Features:

• High Perf. Friction Materials
• Complete Overhaul Gasket Set
• Modification Components
• Replacement Valves
• Replacement Springs

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

Energy Suspension performance bump stops help cushion a collapsing suspension, preventing bottoming-out and expensive vehicle damage. Hyper-Flex performance polyurethane bump stops for control arms, traction bars, leaf springs, etc. are guaranteed to last longer and operate more efficiently than original rubber stops. The smaller, general purpose bullet shaped snubber is ideal for control arms. the low profile button head is for use when clearance is limited. Our large competition race style bump stops smooth out compression better and have a large reinforced metal plate welded to the mounting plate and molded-in. Each style is specially designed for a perfect and custom fit and each style has it’s own durometer, hardness, characteristics. Energy’s wide selection of bump stops are available in red or black color.

Product Features:

• Made of Superior Hyper-Flex+ Material
• Helps Prevent Damage to Control Arm

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

• Made from HYPER-Flex Polyurethane
• Allows Vehicle to Work At Maximum Efficiency
• Easy to Install
• Superior Performance and Greater Longevity
• Lasts Much Longer Than OEM Rubber End Links

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

HEAVY DUTY-Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. STREET/STRIP-Positive shifts for high performance street use or for competitive events. Hardest, quickest possible shift.

Product Features:

• Provides Crisp Shifts
• On Any Stock Automatic Transmission
• Eliminates Soft/Sluggish Shift
• Eliminates Shift Overlap
• Eliminate Clutch and Band Wear

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque