Chevrolet Monte Carlo Performance Ignition Products

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

• Extra Thick Contact Arms
• Large Radius Tungsten Contacts
• High Strength Phenolic Rubbing Blocks
• Prevents Points Float
• Moisture-Proof Buna-N Condenser

Distributor Condenser

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

• Externally mounted coil
• Increases reliability
• Increase performance
• High quality plastic
• Resist spark loss
• Use brass conductors
• Low resistance connections
• No modifications

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

• 42000 Volts
• Effective To 6500 RPM
• Quicker Starting
• Improved Throttle Response
• Higher RPM Power
• Can Finished In Yellow

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-31
• MSD 8225

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

• 7 in. Diameter
• Absolutely the most accurate way to trigger the ignition.
• The non-magnetic pickup cannot be false triggered.
• Powerful magnets are embedded in a billet aluminum trigger wheel.

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

• 6.25 in. Diameter
• Absolutely the most accurate way to trigger the ignition.
• The non-magnetic pickup cannot be false triggered.
• Powerful magnets are embedded in a billet aluminum trigger wheel.

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

Custom Fit Spark Plug Wire Set

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Bolt-on Performance

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

• Adjustable Vacuum Advance
• Increases Horsepower And Throttle Response
• Includes Allen Wrench For Adjustments
• Instantly Increase Horsepower
• Maximum Possible Spark Advance
• Not Legal For Sale/Use In CA

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Product Features:

• Service Part
• Makes Connections Quick And Easy

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• More Accurate Ignition Timing
• Improves Performance And Fuel Economy
• Provides More Accurate Ignition Timing
• Easy To Install w/Hand Tools
• Reduced Maintenance
• Thermal Clad Based Surface Mount Construction
• Utilizes Specialized Electronic Circuitry
• Ignition Timing Is Stable From 1 To 10000rpm