from

$27.99

Product Features:

Application matched component to ensure the system can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$30.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

Zinc plated Grade 5 steel
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Ideal For Minimal Space
12-Point Head And Flange
Zinc Plated For Protection

from

$14.99

The Edelbrock 94 No. 12462 Carburetor Jets .062″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

from

$33.99

Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.

Product Features:

Rubber Material
For Holley®, Barry Grant, And Demon Gasoline Carburetors
No Hardware Included
50cc Volume
Made iIn The USA

from

$13.99

The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var

Product Features:

Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
Includes Gasket
1/2 in. x 28 Power Valve Thread
For Applications That Prefer To Run Carbs Without The Power Valves
Made In The USA

from

$46.99

Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.

Product Features:

Stamped From 18-Gauge Steel
Triple-Chrome Plated
High-Quality Finish
Great Looks
Works With All 5.125 in. Carbs
Base Knock-Outs For Use w/Crankcase Ventilation

from

$20.99

The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.

Product Features:

Nitrile Rubber Material
Metering Block Type
Set of 4
Fits Holley® 4160 Carburetors
Made In The USA

from

$20.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Validated for fit, form, and function
Engineered for the sealing repair environment
Unsurpassed quality you can trust

from

$48.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals & distributor gaskets if applicable
For OE replacement, high performance street, drag race and oval track use

from

$4.29

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$14.99

The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45

Product Features:

Fits Holley® Carburetors With Center Hung Fuel Bowl
Includes Adjusting Nut
Includes Locking Screw
Includes O-Ring
Includes Washers

from

$10.49

This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$1350.99

Holley engineers have taken the state-of-the-art Gen 3 Ultra carburetors and created a budget friendly version that is perfect for street/strip applications as well as all out bracket or sportsman drag cars. The new Holley SP Dominator carburetors feature the patent pending Gen 3 main-body which is 5/16″ taller than the previous generation! This new height allowed for larger radius air entries to deliver smoother flow that equates to improved throttle response and consistency. An extended air cleaner flange is incorporated for easy air scoop attachment when using the available air scoop adapter. Other features include all aluminum construction, tunable billet metering blocks, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws. Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

All Aluminum Construction Saves 3.8 lbs. Over Original Models
28% Weight Savings
Shiny With Billet Aluminum Metering Block and Black Hardware
Calibrations Optimized For Todays Race Engines and New Fuels
Fully Machined From Venturi Throat To Throttle Bore For Perf
Annular Booster Deliver Excellent Signal and Throttle Response
Screw In Air Bleeds Offer Precise Tuning Capabilities
Metering Blocks Feature Improved True Gasket Sealing
Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
4 Corner Idle Allows You To Precisely Control Your Idle System
Clear Sight Windows On Fuel Inlet Side For Fuel Level Adjustment
Notched Float and Jet Extension Are Factory Installed

from

$1125.00

Product Features:

Gold Dichromate finish for corrosion resistance
Optimized race calibration
Contoured venturri inlet offers balanced airflow for increased horsepower
Screw in air bleeds for precision tuning capabilities
Dual 30cc accelerator pumps for additional fuel under initial acceleration
Dual feed fuel inlets for constant high volume fuel delivery
4 corner idle allows you to precisely control your idle system
Progressive Secondaries for perfect off the line launches
Stainless steel throttle plates
Includes notched float and jet extensions
Calibrated for gasoline
100% wet-flow tested by Holley technicians to assure it arrives ready to run!

from

$44.99

WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.

Product Features:

Application matched components ensure carburetor can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$479.99

Product Features:

Single Plane with Isolated Plenum
Square Bore Carburetor Mounting Flange
Isolated Water cross-over
Power band: 2500-7500 RPM
Height: Front 4.18″, Rear 5.28″
Port Size: 1.92″ height 1.20″ width

from

$468.99

Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
Black Powder Coated Finish
Non-EGR W/ Oil Fill Tube

from

$411.99

Product Features:

Best for the Ultimate in Street High-Performance
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock Total Power Package Maximizes Gains
Cast Finish

from

$22.99

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

Center Hung Floats
0.11 in. Needle Diameter
Viton® Needle Material
Sold Individually
Non-Adjustable Type

from

$7.49

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$3.29

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$1.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$16.99

Product Features:

The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
Kit includes two black nitrile fuel bowl gaskets.

from

$5.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$1.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes