Chevrolet El Camino Performance Engines

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Precision die-cast for a great fit, these water necks are first polished to a high luster, then chrome plated. Comes with gasket and mounting bolts.

Product Features:

• Prevents Water Leaks
• Precision Die Cast

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Includes: 2 short flat black valve covers 2 valve cover gaskets 1 flat black push-on breather 1 flat black dipstick & tube 1 flat black timing chain cover 1 flat black timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet

Product Features:

• Ideal Starter Kit
• Enhances Appearance

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

VALVE SEALS, O-RING 11/32″ 1 ST

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:

• Contains all the gaskets needed to change out your camshaft
• Fuel Injector O-Ring Not Included
• Meets Performance Standards

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features:

• Nitrile Rubber And High Density Cork
• Will Not Shrink Or Stick

Roller cam lobes are ground flat rather than tapered like a flat tappet cam; it is necessary to provide some means of holding the cam back to the rear of the engine. The thrust button rides between the front of the timing gear and the back of the front cover and can be shimmed for proper end play of the cam. COMP Cams has both the solid nylon button and the roller thrust bearing available for the ultimate in performance.

Product Features:

• .795″ Length
• Ride between the front of the timing gear and the back of the timing cover
• Can be shimmed to achieve proper endplay
• Solid nylon and roller thrust bearing styles available

Product Features:

• Complete Single For Flat Tappet
• 100cc Combustion Chamber Volume
• 290cc Intake/110cc Exhaust Runner Volume
• 2.19 in. Intake/1.88 in. Exhaust Valve Diameter
• 0.562 in. Deck Thickness

Product Features:

• Case-Hardened Tubing
• Welded Ends
• 5/16 in. Diameter
• Use with or without Hardened Steel Guideplates

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

• Cylinder Head Bolts
• Longer-Than-Stock
• High Quality Grade 8 Alloy
• Increase Torque Settings
• Higher Clamp Loads On Gasket

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

Product Features:

• Square Flange Carburetor Mounting
• Special D-Shaped Port Runner Design
• Large Plenum Chamber

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Torque Converter – Traveler Converter (SUV and Light Truck) for GM 1968 to 1981 TH350, TH375B APPLICATION: GM 1968 to 1981 TH350, TH375B (6) (will not fit TH-350C) Provides slightly higher stall speed than stock to improve pulling power at low speeds. New

Product Features:

• Ideal For Motor Homes
• Ideal For Towing Applications
• Precision Pump Drive Tube
• Heavy Duty Needle Bearings
• Furnace Brazed

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

This Mr. Gasket Rear Main Seal is made from Viton&reg: Rubber. This style of rubber can handle high temperature like silicone rubber, but with superior abrasion resistance. Its durability and it’s double, offset lip seal design make it recommended for applications that have high engine vacuum, like racing engines that utilize external vacuum pumps for crankcase evacuation.

Product Features:

• Repairs That Leaky Rear Main Sail
• Viton« Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Viton® Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Upgrade for Rope Seal Equipped Cars or Silicone Rubber Main Seals

These High Energy Die Cast Aluminum Roller Rocker Arms for Chevy V8 396-454 applications are perfect for street and moderate race use. With a 7/16″ stud diameter and 1.7 ratio, the die cast, larger-than-stock body of the rocker arms is made of aluminum for superior strength with light overall weight. High Energy Die Cast Aluminum Roller Rocker Arms from COMP Cams are an affordable option that feature a die cast, aluminum body with a needle bearing fulcrum and roller tip. Designed to be stiffer and more durable, these cost effective rocker arms are capable of providing added valve lift while withstanding the rigors of a performance application. Their specially engineered fulcrum and roller tip create far less friction than sliding factory models to lower oil temperatures, thus improving both response and horsepower. Snap rings are used to hold the trunion and bearings locked in place.

Product Features:

• Cost effective aluminum construction provides superior strength to weight ratio
• Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
• Durable design increases valve lift while withstanding the rigors of moderate race use
• Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

• CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
• Designed for high performance street and race engines
• Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
• Additional clearance, up to 1.650″ O.D. valve spring

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 8″ diameter
• 1970-73, 396-427-454 cu. in.
• 1967-69, 302 cu. in.
• 1965-68, 327 cu. in. hi-performance
• 1970-76, 400 cu. in.
• 1970-73, 350 cu. in.

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque